507712

Dolmar PC-7614V Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
7
Kickback and lock-in
When working with the Power Cutter there is a danger of kickback and lock-in. -
Kickback occurs when the top of the cutting disc is used for cutting (15). -
This causes the Power Cutter to be thrown back toward the user with great force -
and out of control. Risk of injury!
To prevent kickback, observe the following:
Never cut with the section of the cutting disc shown in gure 15. -
Be especially careful when reinserting the disc into cuts that have already
been started!
Lock-in occurs when the cut narrows (crack, or workpiece under stress). -
This causes the Power Cutter to suddenly jump forward, out of control and with -
great force. Risk of injury!
To prevent lock-in, observe the following:
When reinserting the disc into previous cuts, have the Power Cutter running at -
top speed. Always cut at top speed.
Always support the workpiece so that the cut is under tension (16), so that the -
cut does not press together and jam the cutting disc as it proceeds through the
material.
When starting a cut, apply the disc to the workpiece with care. -
Do not just shove it into the material.
Never cut more than one piece at a time! When cutting, make sure that no other -
workpiece comes into contact.
Working behavior / Method of working
Before starting work, check the work area for any hazards (electrical wires, -
inammable substances). Clearly mark the work area (for example with warning
signs or by cordoning off the area).
When working with the Power Cutter hold it rmly by the front and rear handles. -
Never leave the Power Cutter unattended!
Whenever possible run the Power Cutter at the rated arbour speed (see -
“Technical data”).
Only use the Power Cutter during good light and visibility periods. -
Be aware of slippery or wet areas, and of ice and snow (risk of slipping).
Never work on unstable surfaces. Make sure that there are no obstacles in the -
working area, risk of stumbling. Always ensure that you have a safe footing.
Never cut above your shoulder height (17). -
Never stand on a ladder to cut (17). -
Never use the Power Cutter while standing on scaffolding. -
Do not lean over too far when working. When putting down and picking up the -
Power Cutter, do not bend over from the waist, but instead bend in the knees.
Save your back!
Guide the Power Cutter in such a way that no part of your body is within the -
extended swing range of the disc (18).
Use cutting discs only for the materials for which they are designed! -
Do not use the Power Cutter to lift up and shovel away pieces of material and -
other objects.
Important! Before cutting, remove all foreign objects, such as rocks, gravel, nails
etc. from the cutting area. Otherwise, such objects can be ung away by the disc
with great speed. Injury hazard!
When cutting workpieces down to length use a rm support. If necessary, secure -
the workpiece from slipping, but do not steady it with your foot or allow another
person to hold it.
When cutting round items, always secure them against rotation. -
When guiding the Power Cutter by hand, use the side mounting position of the -
cutter attachment only when actually necessary.
Otherwise, always use the central position. This gives the unit a better balance,
for reduced operator fatigue.
15
16
17
18
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info