507712

Dolmar PC-7614V Manual

9
Zoom out
Zoom in
Previous page
1/52
Next page
9
In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water.
DOLMAR offers the right accessories for all wet cutting applications (see also
“SPECIAL ACCESSORIES”).
Remove foreign objects such as sand, stones and nails found within the working -
area. CAUTION: Watch out for electric wires and cables!
The rapid rotation of the cutting disc at the point of contact throws fragments
out of the cut groove at high speed. For your safety, swing the protection
hood down as far as possible behind the cut (23), so that material fragments
are thrown forward, away from the operator.
Mark the cut, and then make a groove about 5 mm (just under 1/5”) along the -
entire length of the planned cut. This groove will then guide the Power Cutter
accurately guring the actual cutoff.
NOTE:
For long, straight cuts we recommend using a trolley (24, see also “SPECIAL
ACCESSORIES”). This makes it much easier to guide the unit straight.
Perform the cut with a steady back-and-forth motion. -
When cutting slabs to size, you need not cut through the entire material thickness -
(creating unnecessary dust). Instead, simply make a shallow groove, and then
knock off the excess material cleanly on a at surface (25).
CAREFUL!
When cutting into lengths, cutting through material, making cutouts, etc., always
make sure to plan the direction and sequence of cuts in such a way that the disc
does not get jammed by the cut-off piece, and that no persons can be injured by
falling pieces.
Transport and storage
Always turn off the Power Cutter when transporting it or moving it from -
place to place on a site (26).
Never carry or move the unit with the engine on or the disc moving! -
Carry the unit only by the tubular (middle) handle with the cutting disc pointing -
behind you (26). Avoid touching the exhaust mufer (burn hazard!)
When moving the Power Cutter over longer distances, use a wheelbarrow or -
wagon.
When transporting the Power Cutter in a vehicle, make sure it is securely -
positioned in such a way that no fuel can leak out.
Always remove the cutting disc before transporting the unit in a vehicle.
The Power Cutter should be stored safely in a dry place. It must not be left -
outdoors! Always dismount the cutting disc before storage. Keep the Power
Cutter away from children.
Before long-term storage and before shipping the Power Cutter, follow the -
instructions in the chapter on “Storage”. ALWAYS empty the fuel tank and
run the carburetor dry.
When putting cutting discs in storage, be careful to: -
Clean and dry them well. -
Store them lying down at. -
Avoid dampness, freezing temperatures, direct sunshine, high temperatures and -
temperature uctuations, as these can cause breakage and splintering.
Always check new cutting discs or cutting discs that have been in storage -
to make sure that they are free of defects.
23
24
25
26
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info