Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of replacement.
፧
Interval of replacement: Initially, every 20 operating hours, and subsequently every 50 operating hours
Recommended oil: SAE10W-30 oil of API Classification SF Class or higher (4-stroke engine oil for automobile)
Oil Change Procedure
Please follow these steps when changing the oil:
(1) Set the blower down on a level surface.
(2) Place a waste oil container under the drainage hole (1) to catch the oil
as it drains out. The container should have a capacity of at least 220 ml
to be able to catch all of the oil.
(3) Loosen the oil drain bolt (2) to let the oil drain out. Be careful not to
allow oil to get on the fuel tank or other parts.
Caution: Be careful not to lose the gasket (aluminum washer) (3). Place
the oil drain bolt (2) in a location where it will not accumulate
dirt.
(4) Remove the oil cap (4). (Removing the oil cap (4) allows the oil to drain
easily.)
Caution: Be sure to set the oil cap (4) down in a location where it will not
accumulate dirt.
(5) As the level of the oil being drained decreases, tilt the blower over on to
the side with the drain so that the oil will completely drain out.
(6) After the oil has completely drained out, tighten the oil drain bolt (2)
securely. If the bolt is not tightly fastened, this may result in an oil leak.
Caution: Do not forget to put the gasket (aluminum washer) (3) back on
when reattaching the drain plug.
(7) Adding oil during the oil change procedure is performed in the same
manner as the separately explained procedure for adding oil whenever
the level is insufficient. Always add oil by filling from the opening under
the oil cap.
(Specified oil level: Approximately 220 ml)
(8) After filling with oil, tighten the oil cap (4) securely to prevent oil leaks.
DANGER
•Before inspection and maintenance, stop the engine and allow it to cool. Remove also the spark plug and plug cap.
−If inspection or maintenance is attempted immediately after engine stop or with the plug cap left attached, the operator may suffer burn
or an accident due to careless startup.
•After inspection and maintenance, be sure to confirm that all parts are assembled. Then, proceed to operation.
DANGER
•In general, the engine main unit and engine oil still remain hot just after the engine is stopped. In replacement of oil, confirm that the
engine main unit and engine oil are sufficiently cooled down. Otherwise, there may remain a risk of scald. In addition just after of the
engine stopping because oil does not finish to return in the oil case, becomes cause of the oil inserting too much.
•If the oil filled above the limit, it may be contaminated or may catch fire with white smoke.
፧
፧
•Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the
relevant laws and regulations. For any points remaining unknown, contact Authorized Service Agent.
•Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 6
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Dolmar PB-7600.4 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Dolmar PB-7600.4 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 3,14 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
