766075

Dogtrace d-control professional 2000 Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
11
Important: Before the programming make sure no one else is using his d-control
professional or other products from the Dogtrace range close by. Your receiver could
accidentally record the code of his transmitter or interference could occure. Thus
could someone else transmit some commands into your receiver. If this occures,
program once again the communication of your receiver with your transmitter.
Programming function buttons A1 / A2 with the rst receiver:
1. Turn ON your transmitter.
2. The receiver must be turned OFF.
3. Move the red target of the transmitter towards the receiver so it comes into the
contact with the red target of the receiver and hold for 5 seconds. The red LED
indicator of the receiver will lit up, afterwards the green LED indicator will lit up.
4. After 5 seconds the receiver LED indicators will ash 3 times green and red colour
simultaneously. Afterwards the green and red LED indicators will start alternately
ashing.
5. Press down A1 or A2 button.
6. Successful pairing is indicated by a long beep tone of the receiver.
Programming function buttons B1 / B2 with the second receiver:
Proceed in the same way as in the previous chapter, only in the point 5 press down
the function button B1 or B2.
When you want to use the transmitter for training only one dog, it is possible to
program all four function buttons A1 / A2 / B1/ B2 with the one receiver. You can also
use this function for the professional training and for programming communication
of one receiver with two dierent transmitters.
Programming function buttons B1 /B2 (or second transmitter) with the rst
receiver:
1. Turn ON your transmitter.
2. The receiver must be turned ON.
3. Move the red target of the transmitter towards the receiver so it comes into the
contact with the red target of the receiver and hold for 5 seconds. The green LED
indicator of the receiver will lit up, afterwards the red LED indicator will lit up.
4. After 5 seconds the receiver LED indicators will ash 3 times green and red colour
simultaneously. Afterwards the green and red LED indicators will start alternately
ashing.
5. Press down B1 or B2 button (or any other function button on the second
transmitter).
6. Successful pairing is indicated by a long beep tone of the receiver.
is also necessary for using all four function buttons with one receiver. d-control
professional is compatible with other d-control professional models. The transmitter
is designed for training two dogs, so you can pair it with two receivers. Function
buttons A1 / A2 are designed for the dog A and function buttons B1 / B2 for the
dog B.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dogtrace d-control professional 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dogtrace d-control professional 2000 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info