Manual Dimplex LAK 14IMR (page 34 of 100) (English, German, French)

798322

Zoom out

Zoom in

1/100

EN-8 452162.66.09a · FD 0108 www.glendimplex.de

English LAK 3IMR - LAK 14ITR

6 Commissioning

6.1 General

To ensure that commissioning is performed correctly, it should

only be carried out by an after-sales service technician author-

ised by the manufacturer. This may be a condition for an addi-

tional warranty (see "Warranty service").

6.2 Preparation

The following items must be checked prior to commissioning:

All of the indoor unit connections must be installed as de-

scribed in Chapter 5.1.

All of the outdoor unit connections must be installed as de-

scribed in Chapter 7.

All valves which could impair the proper flow of the heating

water in the heating circuit must be open.

The air intake and air outlet paths must be clear.

The settings of the heat pump manager must be adapted

to the heating system in accordance with the manager's

operating instructions.

The heating water circuit must be completely filled and

purged.

Ensure that the condensate drain functions properly.

The outflow from the heating water pressure relief valve

must also function correctly.

Purging the heating system:

Ensure that all heating circuits are open, purge the system

at the highest position and refill water if necessary (comply

with static minimum pressure).

6.3 Commissioning procedure

The heat pump is commissioned via the heat pump manager.

Settings should be made in compliance with the HPM's instruc-

tions.

The heating element of mono energy systems should be dis-

connected during commissioning.

At heating water temperatures below 7 °C, commissioning is

not possible. The water in the buffer tank must be heated with

the 2nd heat generator to at least 18 °C.

The following procedure must then be followed to ensure prob-

lem-free commissioning:

1) Close all consumer circuits.

2) Ensure that the heat pump has the correct water flow.

3) Use the manager to select the automatic operating mode.

4) In the special functions menu, start the "Commissioning"

program.

5) Wait until a return temperature of at least 25 °C has been

reached.

6) Now slowly reopen the heating circuit valves in succession

so that the heating water flow rate is constantly raised by

slightly opening the respective heating circuit. The heat-

ing water temperature in the buffer tank must not be al-

lowed to drop below 20 °C during this process. This en-

sures that the heat pump can be defrosted at any time.

7) When all heating circuits are fully open and a return tem-

perature of at least 18 °C is maintained, the commissioning

is complete.

CAUTION!

Operating the heat pump at low system temperatures may

cause the heat pump to break down completely. After a

prolonged power failure, the commissioning procedure

detailed above must be followed.

Heat source

temperature Max. temperature spread

between heating flow and return

flow

by to

-20 °C -15 °C 4 K

-14 °C -10 °C 5 K

-9 °C -5 °C 6 K

-4 °C 0 °C 7 K

1 °C 5 °C 8 K

6 °C 10 °C 9 K

11 °C 15 °C 10 K

16 °C 20 °C 11 K

21 °C 25 °C 12 K

26 °C 30 °C 13 K

31 °C 35 °C 14 K

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex LAK 14IMR in the language / languages: English, German, French as an attachment in your email.

The manual is 7.79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex LAK 14IMR Manual

Product: