546212

DeWalt DWS520 T 3 Manual

35
Zoom out
Zoom in
Previous page
1/148
Next page
ENGLISH
33
1. Set the speed of the plunge saw to level 5.
2. Place the guide rail on a scrap piece of wood.
3. Set the plunge saw on 5 mm cut depth
4. Place the saw on the rear end of the guide rail.
5. Turn the saw on, press it down to the set
cutting depth and cut the splinterguard along
the full length in one contiuous operation. The
edge of the splinterguard now corresponds
exactly to the cutting edge of the blade.
WARNING: To reduce the risk of injury,
ALWAYS secure the guide rail (w) with a
clamp.
Speed Adjustment (fi g. 1)
The speed can be regulated between 1750 and
4000/min using the speed wheel (s). This enables
you to optimise the cutting speed to suit the
material. Refer to the following chart for type of
material and speed range.
Type of Material
to be Cut
Speed
Range
Solid wood (hard, soft) 3–5
Chipboards 4–5
Laminated wood, blockboards,
veneered and coated boards
2–5
Paper and carton 1–3
Wall Cutting (fi g. 7)
1. Place the plunge saw with the outer guard (v)
on a clean, flat floor.
2. Press the shoe (d) with the front side on the
door against the adjusted depth stop.
Dust Extraction (fi g. 1)
Your tool is fitted with a dust extraction outlet (i).
WARNING: ALWAYS connect the
plunge saw to a dust extractor!
WARNING: ALWAYS use a dust
extraction device designed in
accordance with the relevant regulations
regarding dust emission.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: If the saw blade is worn
replace it with a new sharp blade.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the unit with dry air as often as dirt is
seen collecting in and around the air
vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
DEWALT offers saw blades specially designed for
your plunge saw.
Consult your dealer for further information on the
appropriate accessories.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWS520 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWS520 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info