Manual DeWalt DWS520 T 3 (page 33 of 148) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

546212

Zoom out

Zoom in

1/148

ENGLISH

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power

input of this tool (see technical data).The minimum

conductor size is 1.5 mm

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always unplug the tool.

Bevel Adjustment (ﬁ g. 1)

The bevel angle can be adjusted between 0° and

47°.

1. Loosen the bevel adjustment knobs (e).

2. Set the bevel angle by tilting the saw shoe (d)

until the mark indicates the desired angle on

the bevel scale (y).

3. Tighten the bevel adjustment knobs (e).

Changing the Saw Blade (ﬁ g. 2, 3)

1. Press the lock button (l).

2. Press the plunge saw down to stop (blade

change position).

3. Turn the lock lever (m) clockwise until it stops.

4. Press the lock lever (m) down and rotate the

blade until the lock position is found.

NOTE: The blade (k) is now locked and cannot be

turned by hand.

5. Turn the blade clamping screw (n) anti-

clockwise to remove.

6. Remove the outer flange (o) and used blade (k).

Place the new blade on the inner flange (p).

7. Replace the outer flange (o) and blade clamping

screw (n). Turn the screw clockwise by hand.

NOTE: The direction of rotation of the saw blade

and the rotation of the plunge saw MUST be the

same.

8. Tighten the blade clamping screw firmly using

the hex key.

9. Release and turn the lock lever (m) anti-

clockwise until it stops.

10. Move the plunge saw back to top position.

11. Push plunge trigger (a) forward, to lock saw

blade change.

Adjusting the Riving Knife (ﬁ g. 3)

For the correct adjustment of the riving knife (q), refer

to the figure 3. Adjust the clearance of the riving

knife after changing the saw blade or whenever

necessary.

1. Follow Changing the Saw Blade steps 1–4.

2. Loosen the riving adjustment screw (r) with an

hex key and set the riving knife as shown in

figure 3.

3. Tighten the riving knife screw (r).

4. Turn the lock lever (m) anti-clockwise until it

stops.

5. Move the plunge saw back to top position.

6. Push plunge trigger (a) forward, to lock saw

blade change.

Depth of Cut Adjustment (ﬁ g. 4)

The cutting depth can be set at 0 – 59 mm without

guide rail attached; with the guide rail attached:

0 – 55 mm.

1. Loosen the depth adjustment knob (f) and move

the pointer to obtain the correct depth of cut.

2. Tighten the depth adjustment knob (f).

NOTE: For optimal results, allow the saw blade to

protrude from the workpiece by about 3 mm (fig. 4).

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 5)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWS520 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWS520 T 3 Manual

Product: