Manual DeWalt DWS520 T 3 (page 34 of 148) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

546212

Zoom out

Zoom in

1/148

ENGLISH

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the front

handle (h), with the other hand on the main handle

(c).

Switching On and Off (ﬁ g. 1)

Press the on/off switch to turn the plunge saw on.

Guiding the Tool

(ﬁ g. 5, 6)

WARNING:

• ALWAYS secure the workpiece in

such a manner that it cannot move

while sawing.

• ALWAYS push the machine forwards.

NEVER pull the machine backwards

towards you.

• ALWAYS use the plunge saw with

both hands. Put one hand on the

main handle (c) and the second hand

on the front handle (h) as shown in

figure 5.

• ALWAYS use the clamp to hold the

rail to the workpiece as shown in

figure 6.

• Make sure the cord is not in the path

of the saw.

• Use proper hand position to guide the saw

properly.

• The cutting indicator (t) displays the cutting line

for 0° and 47° cuts (without guide rail).

• The blade position indicator (y) shows the blade

position for full plunge.

• For optimum results, clamp the workpiece

bottom up.

CUTTING

1. Place the machine with the front part of the saw

base on the workpiece.

2. Press the on/off switch to turn the saw on.

3. Push the plunge switch (a) forward, press the

saw down to set cutting depth and push it

forward into cutting direction.

PLUNGE CUTS

WARNING: To avoid kickbacks,

the following in-structions MUST be

observed when plunge cutting:

• Place the machine onto the guide rail

and release the anti-kickback knob (u)

by turning it anti-clockwise.

• Turn the machine on and slowly press

the saw down onto the set cutting

depth and push forward in the cutting

direction. The cut indicators (t) display

the absolute front and the absolute

rear cutting points of the saw blade

(dia. 165 mm) at maximum cutting

depth and using the guide rail.

• If kickback happened during the

plunge cut, turn the anti-kickback

knob (u) anti-clockwise to release it

from the rail.

• When you have finished the plunge

cut, turn the anti-kickback knob (u)

clockwise into the lock position.

Guide System (ﬁ g. 1, 5)

The guide rails, which are available in different

lengths, allow for precise, clean cuts and

simultaneously protect the workpiece surface

against damage.

In conjunction with additional accessories, exact

angled cuts, mitre cuts and ﬁtting work can be

completed with the guide rail system.

Securing the workpiece with clamps ensures a

secure hold and safe working.

The guide clearance of the plunge saw must be very

small for best cutting results and can be set with the

two rail adjusters (j).

1. Release the screw inside the rail adjuster to

adjust the clearance.

2. Adjust the knob until saw locks on rail.

3. Rotate knob back until saw slides easily.

4. Hold the rail adjuster in position and lock the

screw again.

NOTE: ALWAYS readjust the system for use with

other rails.

SPLINTERGUARD

The guide rail is equipped with a splinterguard,

which has to be cut to size before the ﬁrst use:

IMPORTANT: ALWAYS read and follow the guide

system instruction before cutting the splinterguard!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWS520 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWS520 T 3 Manual

Product: