Manual DeWalt DWC410 T 1 (page 32 of 144) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

548835

Zoom out

Zoom in

1/144

ENGLISH

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power

input of this tool (see technical data).The minimum

conductor size is 1.5 mm

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Switch (ﬁ g. 1, 2)

WARNING: To avoid the possibility of

the appliance plug or receptacle getting

wet, position the saw to one side of

a wall mounted receptacle to prevent

water from dipping onto the receptacle

or plug. The user should arrange a “drip

loop” in the cord connecting the saw

to a receptacle (fig. 2). The “drip loop”

is that part of the cord below the level

of the receptacle, or the connector if an

extension cord is used, to prevent water

traveling along the cord and coming in

contact with the receptacle.

CAUTION: Before plugging in tool,

always check to see that the switch

actuates properly and returns to the

OFF position when released.

1. Depress and hold the switch (b) to start

operation.

2. For continuous operation, press the lock-on

button (c) and release the switch. To disengage

the locking button, depress then release the

switch.

To Install the Diamond Blade

(ﬁ g. 1, 3)

1. Hold the external flange (e) in place with the

flange wrench provided and use the blade

wrench provided to turn the left-hand threaded

clamp screw (f) clockwise to loosen and

remove.

2. Remove the clamping screw (f) and external

flange (e).

3. Place saw on a stable surface.

4. Place blade (d) on spindle.

5. Using the flange wrench provided, hold the

external flange (e).

6. Turn the clamping screw (f) counterclockwise

to tighten. Use the blade wrench provided to

secure tightly.

7. To remove the blade, reverse this procedure.

Mounting the Wet Cut System

(ﬁ g. 1)

WARNING: Do not use wet cut system

unless tool is protected by a PRCD.

This system minimizes airborne dust particles while

improving cutting quality and blade life.

1. Loosen the depth adjustment knob (m) and pull

shoe (n) to it's minimum depth of cut position.

2. Remove the screw (k) located directly to the

right of the depth adjustment knob (m) mounted

to the casting.

3. Position the water valve assembly such that the

hole in the water valve assembly aligns with the

screw hole located in the casting and the forked

water valve straddles the blade.

4. Secure in place with screw. DO NOT

overtighten the screw; this could damage the

water valve assembly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWC410 T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWC410 T 1 Manual

Product: