551289
24
Zoom out
Zoom in
Previous page
1/97
Next page
19
Charger
Your DEWALT 1 hour charger accepts battery packs
ranging from 9.6 to 14.4 V.
8 Battery pack
9 Release buttons
10 Charger
11 Charging indicator (red)
Dead spindle drive clutch
This screwdriver is equipped with a dead spindle
feature; the spindle does not turn until the fastener is
pressed into the workpiece. This enables fasteners
to be placed onto the drive accessory of a running
screwdriver.
Electrical safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
power corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DEWALT charger is double
insulated in accordance with EN 50144.
Mains plug replacement
(U.K. & Ireland only)
Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorized
DEWALT repair agent or a qualified electrician.
Disconnect the plug from the supply.
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1).
The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective points
in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).
Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
ENGLISH
en - 4
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
Using an extension cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
0.5 mm
2
; the maximum length is 30 m.
Assembly and adjustment
Prior to assembly and adjustment,
always remove the battery pack.
Always switch OFF the tool before
inserting or removing the battery pack.
Battery pack (fig. A)
Charging the battery pack
When charging the battery pack for the first time,
or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles,
the battery pack will attain full capacity. Always check
the mains prior to charging the battery pack. If the
mains is functioning but the battery pack does not
charge, take your charger to an authorised DEWALT
repair agent. Whilst charging, the charger and the
battery pack may become warm to touch. This is a
normal condition and does not indicate a problem.
Do not charge the battery pack at
ambient temperatures <4 °C or >40 °C.
Recommended charging temperature:
approx. 24 °C.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW979 T-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW979 T-1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info