Manual DeWalt DW745 (page 22 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546615

Zoom out

Zoom in

1/100

ENGLISH

7 Do not overreach

Keep proper footing and balance at all times.

8 Stay alert

Watch what you are doing. Use common sense. Do not operate the

tool when you are tired.

9 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees

both hands to operate the tool.

10 Connect dust extraction equipment

If devices are provided for the connection of dust extraction and

collection facilities, ensure that these are connected and properly

used.

11 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from

the tool before operating the tool.

12 Extension cables

Before use, inspect the extension cable and replace if damaged.

When using the tool outdoors, only use extension cables intended for

outdoor use and marked accordingly.

13 Use appropriate tool

The intended use is described in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Do not force the tool.

Warning! The use of any accessory or attachment or performance of

any operation with this tool other than those recommended in this

instruction manual may present a risk of personal injury.

14 Check for damaged parts

Before use, carefully check the tool and mains cable for damage.

Check for misalignment and seizure of moving parts, breakage of

parts, damage to guards and switches and any other conditions that

may affect its operation. Ensure that the tool will operate properly

and perform its intended function. Do not use the tool if any part is

damaged or defective. Do not use the tool if the switch does not turn

it on and off. Have any damaged or defective parts replaced by an

authorised D

E WALT repair agent. Never attempt any repairs yourself.

15 Unplug tool

Switch off and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use,

before changing any parts of the tools, accessories or attachments

and before servicing.

16 Avoid unintentional starting

Be sure that the tool is switched off before plugging in.

17 Do not abuse cord

Never pull the cord to disconnect from the socket. Keep the cord

away from heat, oil and sharp edges.

18 Store idle tools

When not in use, tools must be stored in a dry place and locked up

securely, out of reach of children.

19 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Keep all handles and switches dry, clean and free from

oil and grease.

20 Repairs

This tool is in accordance with the relevant safety regulations. Have

your tool repaired by an authorised D E WALT repair agent. Repairs

should only be carried out by qualiﬁ ed persons using original spare

parts; otherwise this may result in considerable danger to the user.

Additional safety rules for saw benches

• Do not use saw blades with a body thickness greater or a width of

tooth smaller than the thickness of the riving knife.

• Make sure that the blade rotates in the correct direction and that the

teeth are pointing to the front of the saw bench.

• Be sure all clamp handles are tight before starting any operation.

• Be sure all blade and ﬂ anges are clean and the recessed sides of the

collar are against the blade. Tighten the arbor nut securely.

• Keep the saw blade sharp and properly set.

• Make sure that the riving knife is adjusted to the correct distance

from the blade - maximum 5 mm.

• Never operate the saw without the upper and lower guards in place.

• Keep your hands out of the path of the saw blade.

• Disconnect the saw from the mains supply before changing blades or

carrying out maintenance.

• Use a push stick at all times, and ensure that you do not place hands

closer than 150 mm from the saw blade while cutting.

• Do not attempt to operate on anything but the designated voltage.

• Do not apply lubricants to the blade when it is running.

• Do not reach around behind the saw blade.

• Always keep the push stick in its place when not in use.

• Do not stand on top of the unit.

• During transportation make sure that the upper part of the saw blade

is covered, e.g. by the guard.

• Do not use the guard for handling or transportation.

• Immediately replace the table insert when worn or damaged.

• Check that the workpiece is properly supported. Always provide

additional support for long workpieces.

• Do not exert side pressure on the saw blade.

• Never cut light alloy. The machine is not designed for this application.

• Do not use abrasive disc or diamond cutting wheels

• Rebating, slotting or grooving is not allowed.

• In case of an accident or machine failure, immediately switch the

machine off and pull the plug. Report the failure and mark the

machine in suitable form which prevents that other persons use the

defective machine.

• When the saw blade is blocked due to abnormal feed force during

cutting, ALWAYS switch the machine off and disconnect from power

supply. Remove the workpiece and ensure that the saw blade runs

free. Turn the machine on and start a new cutting operation with

reduced feed force.

• Pull the plug from the socket when blade change or any maintenance

is needed.

• Wear always hear protection.

• Wear always safety glasses

• Wear always dust mask when sawing wood.

Saw blades

• The max. allowable speed of the saw blade must always be equal to or

greater than the no-load speed of the tool speciﬁ ed on the nameplate.

• Do not use saw blades that do not conform to the dimensions stated

in the technical data. Do not use any spacers to make a blade ﬁ t onto

the spindle. Use only the blades speciﬁ ed in this manual, complying

with EN 847-1.

• Consider applying specially designed noise-reduction blades.

• Do not use HSS blades.

• Do not use cracked or damaged saw blades.

• Always choose a suitable saw blade for your application.

• Always wear gloves for handling saw blades and rough material.

Saw blades should be carried in a holder wherever practicable.

Residual risks

The following risks are inherent to the use of saws:

- injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be

avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the rotating saw

blade.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW745 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW745 Manual

Product: