Manual DeWalt DW710 (page 24 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545001

Zoom out

Zoom in

1/80

en - 3 14

ENGLISH

• Take the time to thoroughly read and understand this manual prior to

operation.

• Remove the saw from the packaging material carefully.

• Remove the 4 hex. headed screws securing the machine to the

wooden packaging.

• Release the head lock down knob (14) to raise the head of the

machine.

Description (fig. A1 - A4)

1 Bevel locking handle

2 Rotating table locking knobs

3 Mitre fence

4 Plastic feet

5 Plastic handles/work supports

6 Head lock up release lever

7 Switch

8 Additional saw bench table locking knob

9 Moveable lower blade guard

10 Adjustable cut - to length gauge/material support (optional accessory)

11 Rotating work table

12 Steel base

13 Mitre latch lever

14 Head lock down knob

15 Saw bench table

16 Riving knife

17 Upper saw blade guard

18 Rip fence

19 Fixed lower guard (for use in bench saw position)

Optional accessories

20 Material clamp*

9 Adjustable cut - to length gauge/material support*

* refer to sales literature

Electrical safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Mains plug replacement (U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

authorized DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin

marked E or .

Using an extension cable

If an extension cable is required, use an approved triple-core extension

cable suitable for the power input of this tool (see technical data).

The minimum conductor size is 1.5 mm

. When using a cable reel, always

unwind the cable completely. Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always unplug the tool.

Fitting and adjusting the side handles (fig. B1 - B3)

The machine is supplied with two plastic side handles (5) for easy holding

of the base when carrying.

These handles are constructed in two parts in order to be adjustable.

They also act as material supports on each side of the base.

• To mount, take one flat part (22) and one part with a curved edge (21)

and place the serrated surfaces together. The serrations allow

adjustment, whilst firmly locking them together (fig. B1).

• Place the handles against the side of the base (12), lining up the holes

in the handles with the set of holes nearest to the front provided in the

base. Ensure the curved edge is to the top and pointing to the centre

of the table (fig. B2).

• Using the flat HD screws M6 x 16, four washers D6 and four Hex nuts

M6, screw the handles on loosely. Check that the flange on the bottom

of the flat section is under the edge of the base.

• Having mounted both handles, take a piece of flat wood and lay it up

against the mitre fence (3) and across the table. Ensure that the tops of

the handles are touching the wood (fig. B3).

• Now firmly tighten all bolts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW710 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW710 Manual

Product: