Manual DeWalt DW710 (page 23 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545001

Zoom out

Zoom in

1/80

ENGLISH

Additional safety rules for mitre saws

21 Guard actuation

The blade guard on your saw will automatically raise when the arm is

brought down; it will lower over the blade when the arm is raised.

The guard can be raised by hand when installing or removing saw

blades or for inspection of the saw. Never raise or lower the blade

guard manually unless the saw is turned OFF.

22 Saw blades

Make sure that the blade rotates in the correct direction. Keep the

blade sharp. Do not use blades of larger or smaller diameter than

recommended. For proper blade rating refer to the technical data.

23 Blade guards

Never operate the saw without the guards in place.

24 Mind your hands

Keep your hands out of the path of the saw blade. Never place them in the

blade area when the saw is connected to the electrical power source.

25 Stopping the motor

Raise the blade from the kerf in the workpiece prior to releasing the

switch. Never attempt to stop the machine in motion by jamming a tool

or similar against the blade. Do not wedge anything against the fan to

hold the motor shaft.

26 Maintenance of the blade and arbour collars

Make sure that the blade is not damaged or cracked and that the

arbour collars are clean on the surfaces of contact. Use both wrenches

to tighten.

Additional safety rules for saw benches

27 Saw blades

Make sure that the blade rotates in the correct direction and that the

teeth are pointing to the front of the saw bench.

28 Riving knife

Make sure that the riving knife is adjusted to the correct distance form

the blade - maximum 5 mm.

29 Blade guards

Never operate the saw without the upper and lower guards in place.

30 Push stick

Use a push stick at all times, and ensure that you do not place hands

closer than 150 mm from the saw blade while cutting.

31 Material

Do not use the saw for cutting any material other than wood.

Package contents

The package contains:

1 Assembled table top mitre saw

1 Rip fence

1 Top guard for bench saw position

1 Bottom guard for bench saw position

1 Push stick

1 Plastic bag containing:

2 pairs black plastic handles (2 flat & 2 curved end)

4 flat head screws M6 x 16

4 washers D6

4 hex. nuts M6

1 Allen Key 4 mm

1 Allen key 6 mm

1 spanner 10/13 mm

1 dust extraction adapter

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

13 en - 2

4 Keep children away

Do not let children come into contact with the tool or extension cord.

Keep all people away from the work area.

5 Extension cords for outdoor use

When the tool is used outdoors, always use extension cords intended

for outdoor use and marked accordingly.

6 Store idle tools

When not in use, Power Tools must be stored in a dry place and

locked up securely, out of reach of children.

7 Dress properly

Do not wear loose clothing or jewellery. They can be caught in moving

parts. Preferably wear rubber gloves and non-slip footwear when working

outdoors. Wear protective hair covering to keep long hair out of the way.

8 Wear safety goggles

Also use a face or dust mask in case the operations produce dust or

flying particles.

9 Beware of maximum sound pressure

Take appropriate measures for the protection of hearing if the sound

pressure of 85 dB(A) is exceeded.

10 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees both

hands to operate the tool.

11 Do not overreach

Keep proper footing and balance at all times.

12 Avoid unintentional starting

Do not carry the plugged-in tool with a finger on the switch. Be sure

that the switch is released when plugging in.

13 Stay alert

Watch what you are doing. Use common sense. Do not operate the

tool when you are tired.

14 Disconnect tool

Shut off power and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use, before

servicing or changing accessories.

15 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

16 Use appropriate tool

The intended use is laid down in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Warning! The use of any accessory or attachment or performance of

any operation with this tool, other than those recommended in this

instruction manual may present a risk of personal injury.

17 Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the socket.

Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Inspect the tool cords at regular intervals and, if

damaged, have them repaired by an authorized DEWALT repair agent.

Inspect the extension cords periodically and replace them if damaged.

Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts

Before using the tool, carefully check it for damage to ensure that it will

operate properly and perform its intended function. Check for misalignment

and seizure of moving parts, breakage of parts and any other conditions that

may affect its operation. Have damaged guards or other defective parts

repaired or replaced as instructed. Do not use the tool if the switch is

defective. Have the switch replaced by an authorized DEWALT repair agent.

20 Have your tool repaired by an authorized DEWALT repair agent

This Power Tool is in accordance with the relevant safety regulations.

To avoid danger, electric appliances must only be repaired by qualified

technicians.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW710 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW710 Manual

Product: