790837

DeWalt DCE085R Manual

9
Zoom out
Zoom in
Previous page
1/112
Next page
9
GB
• If the laser is tilted greater than 10°, the beams will
continually flash 3 times.
5. If the laser beams ash, the laser is not level (or plumb)
and should NOT BE USED for determining or marking level
or plumb. Try repositioning the laser on a level surface.
6. If ANY of the following statements are TRUE, continue with
the instructions for Checking Laser Accuracy BEFORE
USING THE LASER for a project.
• This is the first time you are using the laser (in case
the laser was exposed to extreme temperatures).
• The laser has not been checked for accuracy
in a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory.
It is recommended that you perform an accuracy check prior
to using the laser for the rst time (in case the laser was
exposed to extreme temperatures) and then regularly to ensure
the accuracy of your work. When performing any of the
accuracy checks listed in this manual, follow these guidelines:
• Use the largest area/distance possible, closest to the
operating distance. The greater the area/distance, the easier
to measure the accuracy of the laser.
• Place the laser on a smooth, at, stable surface that is level
in both directions.
• Mark the center of the laser beam.
Plumb Dot Accuracy
Checking the plumb calibration of the laser can be most
accurately done when there is a substantial amount of vertical
height available, ideally 25’ (7.5 m), with one person on the oor
positioning the laser and another person near a ceiling to mark
the dot created by the beam on the ceiling.
1. Mark point P1 on the oor (Figure G #1).
2. Turn the laser ON and press once to display dots
above, ahead, and below the laser.
3. Place the laser so that the down dot is centered over point
P1 and mark the center of the up dot on the ceiling as point
P2 (Figure G #1).
4. Turn the laser 180°, making sure that the down dot is still
centered on point P1 on the oor (Figure G #2).
5. Mark the center of the up dot on the ceiling as point P3
(Figure G #2).
6. Measure the distance between points P2 and P3.
7. If your measurement is greater than the Allowable
Distance Between P2 & P3 for the corresponding
Distance Between Ceiling & Floor in the following table,
the laser must be serviced at an authorized service center.
Distance Between
Ceiling & Floor
Allowable Distance
Between P2 & P3
15′ (4.5m) 7/64”(2.6mm)
20′ (6m) 9/64” (3.3mm)
30′ (9m) 7/32” (5.4mm)
40′ (12m) 9/32” (7.2mm)
Level Dot Accuracy - Level
Checking the level calibration of the laser unit requires two
parallel walls at least 20’ (6 m) apart.
1. Turn the laser ON and press twice to display dots
above, ahead, below, and to the right and left of the laser.
2. Place the laser 2”–3” (5–8 cm) from the rst wall. To test
the front laser dot, make sure the front of the laser is facing
the wall (Figure H #1).
3. Mark the laser dot position on the rst wall as point P1
(Figure H #1).
4. Turn the laser 180˚ and mark the laser dot position on the
second wall as point P2 (Figure H #1).
5. Place the laser 2”–3” (5–8 cm) from the second wall. To test
the front laser dot, make sure the front of the laser is facing
the wall (Figure H #2), and adjust the height of the laser
until the laser dot hits point P2.
6. Turn the laser 180˚ and aim the laser dot near point P1 on
the rst wall, and mark point P3 (Figure H #2).
7. Measure the vertical distance between points P1 and P3 on
the rst wall.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE085R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE085R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info