790837

DeWalt DCE085R Manual

11
Zoom out
Zoom in
Previous page
1/112
Next page
11
GB
Turning the Laser Off
Slide the Power/Transport Lock switch to the OFF/Locked
position (Figure A #1a) when the laser is not in use. If the
switch is not placed in the Locked position, all 4 LEDs will
remain lit on the Battery Meter on the keypad ( A #3).
Using the Pivot Bracket
The laser has a magnetic pivot bracket (Figure B #3, Figure
D #1) permanently attached to the unit.
WARNING:
Position the laser and/or wall mount on a stable
surface. Serious personal injury or damage to the
laser may result if the laser falls.
• The bracket has magnets (Figure B #2) which allow the unit
to be mounted to most upright surfaces made of steel or iron.
Common examples of suitable surfaces include steel framing
studs, steel door frames, and structural steel beams.
• The bracket has a keyhole slot (Figure B #1) so it can be
hung from a nail or screw on any kind of surface.
Using the Laser with Accessories
WARNING:
Since accessories other than those offered by
DeWALT have not been tested with this laser, use of
such accessories with this laser could be hazardous.
Only use DeWALT accessories that are recommended for use
with this model. Accessories that may be suitable for one laser
may create a risk of injury when used with another laser.
The bottom of the laser is equipped with 1/4-20 and 5/8-11
female threads (Figure C) to accommodate current or future
DeWALT accessories. Only use DeWALT accessories specied
for use with this laser. Follow the directions included with the
accessory.
Recommended accessories for use with this laser are available
at extra cost from your local dealer or authorized service center.
If you need assistance locating any accessory, please contact
your nearest DeWALT service center or visit our website:
http://www.dewalt.eu.
Using the Laser with the Ceiling Bracket
The laser ceiling bracket (if included) offers more mounting
options for the laser. The ceiling mount has a clamp at one
end which can be xed to a wall angle for acoustic ceiling
installation. At each end of the ceiling mount is a screw hole to
allow it to be hung from a nail or screw on any kind of surface.
Once the ceiling mount is secured, its steel plate provides
a surface to which the magnetic pivot bracket can be attached.
The position of the laser can then be ne-tuned by sliding the
magnetic pivot bracket up or down on the wall mount.
Maintenance
• When the laser is not in use, clean the exterior parts with
a damp cloth, wipe the laser with a soft dry cloth to make
sure it is dry, and then store the laser in the kit box provided.
• Although the laser exterior is solvent resistant, NEVER use
solvents to clean the laser.
• Do not store the laser at temperatures below -20 ˚C (-5 ˚F )
or above 60 ˚C (140 ˚F).
• To maintain the accuracy of your work, check the laser often
to make sure it is properly calibrated.
• Calibration checks and other maintenance repairs may be
performed by DeWALT service centers.
Troubleshooting
The Laser Does Not Turn On
• If AA batteries are being used, make sure:
• Each battery is installed correctly, according to (+) and (–)
listed inside the battery compartment.
• The battery contacts are clean and free of rust or
corrosion.
• The batteries are new, high-quality, name brand batteries
to reduce the chance of battery leakage.
• Make sure the AA batteries or Li-ion rechargeable pack are
in proper working condition. If in doubt, try installing new
batteries.
• Be sure to keep the laser dry.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE085R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE085R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info