790944

DeWalt DCE080GS Manual

25
Zoom out
Zoom in
Previous page
1/232
Next page
25
GB
The back of the grade rod is designed to measure the height of
ceilings, joists, etc. Fully extend the top section of the grade rod until
the button locks into the previous section. Extend that section either
until it locks into the adjacent section or until the grade rod touches
the ceiling or joist. The height is read where the last extended section
exits the previous lower section (Figure Q).
Target Card
Some laser kits include a Laser Target Card (Figure R) to aid in
locating and marking the laser beam. The target card enhances the
visibility of the laser beam as the beam crosses over the card. The
card is marked with standard and metric scales. The laser beam
passes through the red plastic and reflects off of the reflective tape
on the reverse side. The magnet at the top of the card is designed to
hold the target card to ceiling track or steel studs to determine plumb
and level positions. For best performance when using the Target
Card, the DeWALT logo should be facing you.
Laser Enhancement Glasses
Some laser kits include Laser En hancement Glasses (Figure S).
These glasses improve the visibility of the laser beam under bright
light conditions or over long distances when the laser is used for
interior applications. These glasses are not required to operate the
laser.
CAUTION:
These glasses are not ANSI approved safety glasses and
should not be used while operating other tools. These
glasses do not keep the laser beam from entering your
eyes.
CAUTION:
To reduce the risk of serious injury, never stare directly into
the laser beam with or without these glasses.
Maintenance
Laser Cleaning and Storage
• Under some conditions, the glass lens may collect some dirt or
debris. This will affect beam quality and operating range. The lens
should be cleaned with a cotton swab moistened with water.
• The flexible rubber shield can be cleaned with a wet lint-free
cloth such as a cotton cloth. USE WATER ONLY — DO NOT use
cleansers or solvents. Allow the unit to air dry before storing.
• To maintain the accuracy of your work, check the calibration of the
laser often. Refer to Checking the Calibration.
• Calibration checks and other maintenance repairs can be
performed by DEWALT service centers. Two free calibration checks
are included under the DEWALT One Year Free Service Con tract.
• When the laser is not in use, store it in the kit box provided.
• Do not store your laser in the kit box if the laser is wet. Dry exterior
parts with a soft, dry cloth and allow the laser to air dry.
• Do not store your laser at temperatures below 0˚F (-18˚C) or above
105˚F (41˚C).
WARNING:
Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may
weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any
liquid get inside the unit; never immerse any part of the unit
into a liquid. Never use compressed air to clean the laser.
Detector Cleaning and Storage
• Dirt and grease may be removed from the exterior of the detector
using a cloth or a soft, non-metallic brush.
• The DEWALT Digital Laser Detector is waterproof. If you should
drop the detector in mud, wet concrete, or a similar substance,
simply hose the detector off. Do not use high pressure water (e.g.,
from a pressure washer).
• The best storage place is one that is cool and dry, and away from
direct sunlight and excess heat or cold.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE080GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE080GS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info