Manual DeWalt DC232 (page 39 of 168) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

446534

Zoom out

Zoom in

1/168

ENGLISH

• For LH-users, slide the side handle clamp over

the collar behind the tool holder, handle at the

right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (ﬁ g. F)

• Insert the required drill bit.

• Slacken the side handle (9).

• Fit the depth adjustment rod (8) through the

hole in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/reverse slider (ﬁ g. G)

• Push the forward/reverse slider (2) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (2) to the RH-

side for reverse (LH) rotation.

CAUTION: Always wait until the motor

has come to a complete standstill

before changing the direction of

rotation.

DC229/DC234 - Replacing the tool holder with

the chuck (ﬁ g. H)

• Turn the locking collar (6) into the unlocking

position and pull the tool holder (5) off.

• Push the chuck (16) onto the spindle and turn

the locking collar into the locking position.

• To replace the chuck with the tool holder, ﬁ rst

remove the chuck the same way as the tool

holder was removed. Then place the tool holder

the same way as the chuck was placed.

CAUTION: Never use standard chucks

in the hammer drilling mode.

Replacing the dust cover (ﬁ g. D)

The dust cover (7) prevents dust ingress into the

mechanism. Replace a worn dust cover immediately.

• Pull back the tool holder locking sleeve (15) and

pull the dust cover (7) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

Instructions for use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the tool

(approx. 5 kg). Excessive force does

not speed up drilling but decreases tool

performance and may shorten tool life.

• Do not drill or drive too deep to prevent

damage to the dust cover.

Always hold the tool ﬁ rmly with both

hands and ensure a secure stance .

Always operate the tool with the side

handle properly mounted.

• If the cutting tool is no longer sharp,

replace with a new cutting tool.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Make sure the battery pack is properly seated.

Switching on and off (ﬁ g. A)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in off position, move the

forward/reverse slider (2) to the central position.

Hammer drilling (ﬁ g. A)

• Set the mode selector switch (3) to the

"hammer drilling" position.

• Insert the appropriate drill bit. For best results

use high quality carbide-tipped bits.

• Adjust the side handle (9) as required.

• If necessary, set the drilling depth.

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and switch on the

tool.

Rotary drilling (ﬁ g. A)

• Set the mode selector switch (3) to the "rotary

drilling" position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC232 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC232

DeWalt DC232 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 204 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC232 Manual

Product: