Manual DeWalt DC232 (page 37 of 168) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

446534

Zoom out

Zoom in

1/168

ENGLISH

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only ﬁ t 13 Amperes BS1363A approved plugs

ﬁ tted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to their

respective points in the plug (see below). Brown

is for Live (L) (2) and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable ﬁ rmly and that the two

leads are correctly ﬁ xed at the terminal screws.

WARNING: Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size

is 1 mm

; the maximum length is 30 m.

Assembly and adjustment

WARNING: Prior to assembly and

adjustment, always remove the battery

pack.

WARNING: Always switch off the tool

before inserting or removing the battery

pack.

WARNING: Use only D E WALT battery

packs and chargers.

Fitting and removing the battery pack (ﬁ g. A)

• To ﬁ t the battery pack (11), line it up with the

receptacle on the tool. Slide the battery pack

into the receptacle and push until the battery

snaps into place.

• To remove the battery pack, push the release

button (12) while at the same time pulling the

battery pack out of the receptacle.

Charging the battery pack (ﬁ g. A & B)

Always check the mains prior to charging the

battery pack. If the mains is functioning but the

battery pack does not charge, take your charger to

an authorized D

E WALT repair agent.

Whilst charging, the charger and the battery pack

may become warm to touch. This is a normal

condition and does not indicate a problem.

CAUTION:

Do not charge the battery

pack at ambient temperatures < 4 °C

or > 40 °C. Recommended charging

temperature: approx. 24 °C.

• To charge the battery pack (11), insert it into the

charger (13) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicators (14) will blink

according to the state of charge of the battery pack.

• When ﬁ nished charging, the indicators are

all on. The charger automatically switches to

equalise mode.

• The battery pack can be removed at any time or

left in the connected charger indeﬁ nitely.

• The red charging indicators ﬂ ash rapidly to

indicate a charging problem. Reinsert the

battery pack or try a new one. If the new pack

also refuses to charge, have your charger

tested by an authorized D e WALT repair agent.

• The red charging indicators ﬂ ash rapidly with

one short blink followed by a long blink to

indicate a problem with the charger. Return the

charger to an authorized D e WALT repair agent.

• When plugged into power sources such as

generators or sources that convert DC to

AC, the red charging indicators (14) may

ﬂ ash together with two fast blinks followed

by a pause. This indicates a temporary

problem of the power source. The charger will

automatically switch back to normal operation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC232 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC232

DeWalt DC232 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 204 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DC232 Manual

Product: