446534

DeWalt DC232 Manual

38
Zoom out
Zoom in
Previous page
1/168
Next page
36
ENGLISH
Charging process (fi g. B)
Refer to the table below for the state of charge of
the battery pack.
State of charge
1 light blinkling < 33%
1 light blinkling, 1 light on 33-66%
1 light blinkling, 2 lights on 66-99%
3 lights on 100%
Automatic refresh
• The automatic refresh mode will equalize or
balance the individual cells in the battery pack
at its peak capacity. Battery packs should be
refreshed weekly or whenever the pack no
longer delivers the same amount of work.
• To refresh your battery pack, place the battery
in the charger as usual. Leave the battery pack
for at least 8 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
Deep discharge protection
The battery pack is protected against deep
discharging when it is used in the tool.
Selecting the operating mode (fi g. C1 & C2)
DC228/DC232 (fi g. C1)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling.
DC229/DC234 (fi g. C2)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling.
Hammering only: for light chipping.
• To select the operating mode, press the safety
lock (4) and rotate the mode selector switch
(3) until it points to the symbol of the required
mode.
• Release the safety lock and check that the
mode selector switch is locked in place.
WARNING: Do not select the operating
mode when the tool is running.
Inserting and removing SDS-plus accessories
(fi g. D)
Your rotary hammer drill uses SDS-plus
accessories (refer to the inset in fi g. D for a cross-
section of an SDS-plus
bit shank).
• Clean and grease the bit shank.
• Insert the bit shank into the tool holder (5).
• Push the bit down and turn it slightly until it fi ts
into the slots.
• Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
• To remove a bit pull back the tool holder locking
sleeve (15) and pull out the bit.
Fitting the side handle (fi g. E)
The side handle (9) can be fi tted to suit both
right-hand and left-hand users.
WARNING: Do not use the tool without
the side handle properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the left.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC232 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC232 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC232

DeWalt DC232 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info