544945
24
Zoom out
Zoom in
Previous page
1/100
Next page
24
ENGLISH
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Fitting and removing an air hose (fig. A)
The unit is equipped with 2 air hose connectors.
Fitting
Push the male end of the air hose in the
connector (2).
Check wheter the air hose has been connected
properly.
Removing
Push the male end of the air hose further in the
connector (2).
Push in the collar of the connector.
Remove the air hose by pulling the male end out
of the connector.
Release the collar.
Before fitting or removing an air hose,
always make sure the pressure is off the
tank.
Adjusting the air pressure (fig. A)
The pressure available at the air hose can be adjusted
to the pressure rating of the tool or accessory to be
connected to this unit.
Pull out the adjustment knob (4).
Adjust the air pressure by turning the knob.
The air pressure can be read from the gauge (3).
- To increase the air pressure, turn the knob into
the clockwise direction.
- To decrease the air pressure, turn the knob
into the anticlockwise direction.
Push the knob in the locking position when the
required pressure has been set.
Always check the maximum pressure
rating of the tool or accessory to be
connected to the unit.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Putting the unit into operation
Check the pump oil level.
Ensure that the tank is drained properly.
Check that the safety valves are functioning
properly.
Connect the air hose to the unit and adjust the air
pressure.
Switch on the unit.
Allow the unit to build up pressure. The motor
automatically stops running as soon as the cut-
out pressure has been reached.
The motor automatically starts running as soon
as the tank pressure drops below the cut-out
pressure.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D55155 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D55155 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info