Manual DeWalt D55155 (page 25 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544945

Zoom out

Zoom in

1/100

ENGLISH

Putting the unit out of operation

• Switch off the unit.

• Allow the unit to cool down.

• Shut the air pressure adjustment knob and

disconnect the air hose.

• Drain the tank.

Switching on and off (fig. B)

• To switch the unit on, turn the switch (1) into

position I.

• To switch the unit off, turn the switch (1) into

position 0.

Always switch off the unit before

uplugging.

Motor thermal overload (fig. C)

The unit has a thermal overload protector: in case of

motor overheat, the power supply to the motor will

be cut off.

• When the thermal overload engages, switch the

unit off and wait for the motor to cool down.

• Press the thermal overload reset button (7) firmly

until a click is heard.

• Switch the unit on. The unit is ready again for

operation.

Optional accessories

Depending on the application, the following

accessories may be required:

• An air-line filter for removal of moisture and oil

vapor in compressed air.

• An in-line lubricator to prolong the life of air tools.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

• As a precaution regularly check for the following

conditions:

- leaks to the tank

- leaks to the oil system

- unusual noise or vibration to the running motor

Draining the tank (fig. D)

Before fitting an air hose or performing any

maintenance, or when putting the unit out of

operation, the tank must be drained.

• Lift the unit to provide access to the drain valve.

• Take hold of the drain valve lever (8) and slowly

rotate the lever so as to gradually bleed air from

the tank.

• When the pressure is at 0.7 bar, turn the valve

into the fully open position.

• Hold the unit at an angle of approx. 10° to

remove any moisture or dirt out of the tank.

• Check whether the tank pressure gauge reads 0

bar to be sure the pressure is off the tank.

• Close the drain valve.

Changing the pump oil (fig. C)

At first use, the pump oil must be changed after

50 hours of operation. Thereafter, the pump oil must

be changed every 200 hours or at least at a 3 month

interval.

• Place a suitable container under the drain plug (9).

• Remove the dipstick (6).

• Remove the drain plug.

• Allow ample time for the oil to drain. Hold the unit

at an angle of approx. 10° to help the oil flow

towards the drain plug.

• After the oil has been drained, re-install the drain

plug.

• Fill the reservoir.

• Re-install the dipstick.

Checking the oil level (fig. E)

The oil level must be checked on a daily basis.

• Remove the dipstick (6).

• Wipe the oil off the dipstick.

• Re-install the dipstick for a few seconds to have

the oil collect on the dipstick.

• Remove the dipstick to check the oil level.

The oil level is correct if the collected oil is

between the markings (10).

• If the oil level is below the lower marking,

add extra oil.

Checking the air filter (fig. C)

The air filter must be checked on a weekly basis.

After 200 hours the air filter must be replaced.

• Remove the filter (11) from the pump head.

• Separate the filter body into two halves.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D55155 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D55155 Manual

Product: