546470

DeWalt D51430 Manual

22
Zoom out
Zoom in
Previous page
1/92
Next page
22
ENGLISH
• Increase the air pressure to the normal operating
level.
• Use the tool in the normal manner.
Hot weather operation
The tool should operate normally. Avoid the heat of
direct sunlight to avoid damage to the bumpers,
o-rings, and other rubber parts.
Actuating the tool (fig. A)
The tool can be operated using one of two modes.
The trigger installed on the tool determines the
mode of actuation.
Sequential action mode
The sequential action mode is used for intermittent
fastening when very careful and accurate placement
is desired.
• Fit the grey trigger as described above.
• Release the trigger lock (2).
• Push the contact trip (4) against the work surface.
• Pull the trigger (1) to actuate the tool.
Each trigger pull with the contact trip pushed
against the work surface will drive one fastener.
Bump action mode
The bump action mode is used for rapid fastening
on flat, stationary surfaces.
• Fit the black trigger as described above.
• Release the trigger lock (2).
• To drive a single fastener: Operate the tool as
described for sequential action.
• To drive several fasteners: Pull the trigger (1) first,
and then push the contact trip (4) repeatedly
against the work surface.
Do not keep the trigger depressed when
the tool is not in use. Keep the trigger
lock engaged to prevent accidental
actuation when the tool is not in use.
Clearing a jammed fastener (fig. E)
If a fastener becomes jammed in the nosepiece,
follow these instructions to remove the fastener:
• Disconnect the airline from the tool.
• Engage the trigger lock (2).
• Remove all fasteners from the magazine.
• Flip up the front latch (13) and move the bracket (14)
out of the way so that barrel (15) can be opened.
• Remove the bent fastener, using pliers if necessary.
• If the driving blade is in the down position, push
the driving blade upward using a screwdriver.
• Close the barrel (15) and put the bracket (14)
back in position.
• Press the front latch (13) into the locked position.
• Feed the fasteners into the nose piece as
described under „Loading the tool“.
If fasteners become jammed in the
nosepiece frequently, have the tool
serviced by an authorised DEWALT
service centre.
Optional accessories
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your DEWALT tool has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends on proper tool care and regular cleaning.
The following maintenance operations must be
performed every day.
Cleaning
• Clean the magazine and the nosepiece using
compressed air.
• Clean the front end of the contact trip using fuel
oil or diesel fuel.
Draining
• Drain all condensation from the air compressor
tanks and hoses.
Lubrication
• Insert 5 - 7 drops pneumatic tool oil into the air
fitting on the end cap of the tool.
Checking
• Ensure that all fasteners on the tool are tight and
undamaged.
• Tighten loose fasteners using the appropriate tool.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51430 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info