Manual DeWalt D51430 (page 21 of 92) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546470

Zoom out

Zoom in

1/92

ENGLISH

Removing the trigger

• Disconnect the airline from the tool.

• Remove all fasteners from the magazine.

• Remove the rubber grommet (8) from the end of

the dowel pin (9).

• Remove the dowel pin.

• Remove the trigger assembly (10).

Fitting the trigger

• Insert the trigger assembly into the trigger cavity,

ensuring that the trigger spring (11) is properly

seated.

• Insert the dowel pin (9) through the tool frame,

contact trip guide and trigger assembly.

• Push the rubber grommet (8) onto the end of the

dowel pin.

Air fitting (fig. A)

These tools have a standard 3/8" pipe thread for the

air fitting (7).

• Wrap the male end of the fitting with Teflon tape

to prevent air leaks.

• Screw the fitting into the end cap and tighten firmly.

Loading the tool (fig. C)

• Lock the magazine latch (6) in the back position.

• Select an appropriate collated fastener stick.

See „Technical data“.

• Place the collated fastener stick (s) onto the

magazine rail (11).

• Release the magazine latch by unlatching the

lever (12).

• Carefully slide the latch forward to press against

the fasteners.

Unloading the tool (fig. C)

• Lock the magazine latch (6) in the back position.

• Remove the collated fastener stick (s) from the

magazine rail (11).

Always disconnect the tool from the air

supply before loading or unloading

fasteners.

Adjusting the driving depth (fig. D)

The driving depth can be adjusted to the type of

fastener used.

• To reduce the depth, press the lock button (12)

and slide the slider (3) downward.

• To increase the depth, press the lock button (12)

and slide the slider (3) upward.

Trigger lock (fig. A)

This tool is equipped with a trigger lock-off switch

which prevents the tool from firing a fastener.

• To engage the trigger lock, push the switch (2) to

the right.

• To release the trigger lock, push the switch to the

center.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Preparing the tool (fig. A)

• Drain all condensation from the air compressor

tanks and hoses.

• Lubricate the tool. See „Maintenance“.

• Remove all fasteners from the magazine.

• Check if the contact trip (4) can move freely.

Do not use the tool if the contact trip

cannot move freely.

• Check that the pressure of the air supply is below

the maximum recommended operating pressure.

• Connect the air hose to the fitting on the tool.

• Check for audible leaks around valves and gaskets.

• Set the air pressure to the minimum required

operating pressure for your application.

Never use a tool that leaks or has

damaged parts.

Cold weather operation

When operating tools at temperatures below freezing:

• Keep the tool as warm as possible before use.

• Disconnect the airline from the tool.

• Put 10 to 15 drops of DEWALT pneumatic tool oil

(or winter-weight pneumatic oil containing

ethylene glycol) into the air inlet.

• Set the air pressure to a maximum of 5.5 bar.

• Connect the air hose to the fitting on the tool.

• Load fasteners into the magazine as described

above.

• Actuate the tool 5 or 6 times into scrap lumber to

lubricate the o-rings.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51430 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D51430 Manual

Product: