548823
9
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH
7
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
Connecting to the Mains
The mains supply to be used for this machine must
be equipped with a 16 A cut-out fuse with time delay.
Voltage Drops
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions, other
equipment may be affected.
If the system impedance of the power supply is lower
than 0.11 Ω, disturbances are unlikely to occur.
Power Supply
Be sure your power supply agrees with the
nameplate marking. A voltage decrease of more
than 10% willcause a loss of power and overheating.
Cutting Capacity
The wide vise opening and high pivot point provide
cutting capacity for many large pieces. Use the
cutting capacity chart to determine total maximum
size of cuts that can be made with a new wheel.
CAUTION: CERTAIN LARGE,
CIRCULAR OR IRREGULARLY
SHAPED OBJECTS MAY REQUIRE
ADDITIONAL HOLDING MEANS
IF THEY CANNOT BE HELD
SECURELY IN VISE.
CAUTION: DO NOT CUT
MAGNESIUM WITH THIS TOOL.
For MAXIMUM CUTTING CAPACITY, please refer
to Table A.
NOTE: Capacity shown on chart assumes no wheel
wear and optimum fence position.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
To Carry (fi g. 1)
Fold down unit to position where you can carry the
saw. Push in lock chain (a) to lock arm down.
Unlocking (fi g. 1)
To unlock tool and raise head, depress motor arm
slightly and pull lock chain (a) out. Motor arm will
then pivot upward.
Proper Hand Position (fi g. 1)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
operating handle (z), with the other hand guiding the
workpiece.
(TABLE A)
Workpiece Shape
90° Cutting Angle
A = 125mm
(4-7/8")
A = 115mm
(4-1/2")
A x B
115mm x 130mm
(4-1/2" x 5-1/8")
102mm x 188mm
(4" x 7-5/8")
76mm x 229mm
(3" x 7-3/8")
A = 115mm x 137mm
(4-1/2" x 5-3/8")
45° Cutting Angle
A= 115mm
(4-1/2")
A = 98mm
(3-13/16")
105mm x 95mm
(4-1/8" x 3-3/4")
A =
95mm (3-3/4")
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28720 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28720 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28720 T 1

DeWalt D28720 T 1 Additional guide - Turkish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info