548823
11
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH
9
WARNING: Check the work surface
that the chop saw rests on when
replacing with a new abrasive wheel. It
is possible that the wheel may contact
ANY ITEMS OR STRUCTURE THAT
EXTENDS ABOVE work surface (under
the base) when the arm is fully lowered.
Operation Tips for More Accurate
Cuts
Allow the wheel to do the cutting. Excessive
force will cause the wheel to glaze reducing
cutting efficiency and/or to deflect causing
inaccurate cuts.
Properly adjust fence angle.
Make sure material is laying flat across base.
Properly clamp material to avoid movement and
vibration.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
tool from power source before
installing and removing accessories,
before making any adjustments or
removing/installing attachments or
accessories. Be sure the trigger switch
is in the OFF position. An accidental
start-up can cause injury.
Motor Brush Inspection and
Replacement (fi g. 9)
Brushes should be regularly inspected for wear. To
inspect brushes, remove the two end cap screws
(v) and remove the end cap (w). Remove brush cap
(y). Brushes (x) should slide freely in brush box. If
brushes are worn down to 8 mm (0.3")as shown in
Figure9, they should be replaced.
To reinstall, push new brush back into brush box. If
replacing existing brush, maintain same orientation
as when removed. Replace the brush cap (Do not
overtighten). Replace end cap and two screws.
Tighten securely.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28720 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28720 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28720 T 1

DeWalt D28720 T 1 Additional guide - Turkish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info