548823
7
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH
5
In operation, avoid bouncing the wheel or
giving it rough treatment. If this occurs, stop
the tool and inspect the wheel for cracks or
flaws.
Clean your chop saw periodically following the
procedure in this manual.
Never use the machine without the guards in
place.
Do not remove base.
ALWAYS USE THE VISE OR SPECIAL
FIXTURE TO CLAMP WORK SECURELY.
Other aids such as spring, bar, or C-clamps
may be appropriate for certain sizes and shapes
of workpiece. Use care in selecting and placing
these clamps and make a dry run before
making a cut.
Use only 355mm (14") type 1 wheels rated at
4100rpm or higher.
Allow cut off parts to cool before handling.
Do not attempt to cut wood or plastic with this
tool.
NEVER CUT MAGNESIUM WITH THIS
TOOL.
Use chop saw in a well-ventilated area.
Turn chop saw off before removing any pieces
from the base.
DO NOT CUT ELECTRICALLY LIVE
MATERIAL.
Do not use circular saw blades or any
other toothed blades with this tool. Serious
injury may result.
DO NOT OPERATE THIS TOOL NEAR
FLAMMABLE LIQUIDS, GASES OR DUST.
Sparks or hot chips from cutting or arcing motor
brushes may ignite combustible materials.
Ensure that the abrasive wheel is correctly fitted
and tightened before use.
Let the tool run at no-load in a safe position
for at least 1 minute. If there is a considerable
vibration or if any other defect occurs, stop the
tool and check it to determine the cause.
Ensure that ventilation slots are kept clear when
working in dusty conditions. First disconnect the
machine from the mains supply then clean the
openings by using a soft brush.
Do not use the side of the abrasive wheel as a
deburring grinder. This will substantially weaken
the wheel creating an unsafe condition. The
wheel may come apart.
The wheel continues to rotate after the machine
is switched off.
WARNING: Wear appropriate
hearing protection during use. Under
some conditions and duration of use,
noise from this product may contribute
to hearing loss.
CAUTION: Spark deflector will get hot.
Avoid touching or adjusting while hot.
Keep cordset and materials away from
spark deflector.
Avoid prolonged contact with dust from
cutting activity Wear protective clothing
and wash exposed areas with soap and
water. Allowing dust to get into your mouth,
eyes, or lay on the skin may promote absorption
of harmful chemicals.
Do not use toothed blades.
Do not expose to rain or use in damp locations.
Only use chop saw wheel of a
max. Thickness of 2.8mm and a
max. Diameter of 355mm (14").
Residual Risks
The following risks are inherent to the use of
these machines:
Injuries caused by touching the rotating
parts.
Injuries caused by disruption of the cutting
disc.
These risks are most evident:
Within the range of operation.
Within the range of the rotating machine
parts.
In spite of the application of the relevant
safety regulations and the implementation of
safety devices, certain residual risks cannot be
avoided. These are:
Impairment of hearing.
Risk of accidents caused by the uncovered
parts of the rotating cutting disc.
Risk of injury when changing the disc.
Risk of squeezing fingers when opening the
guards.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D28720 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D28720 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt D28720 T 1

DeWalt D28720 T 1 Additional guide - Turkish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info