499042
34
Zoom out
Zoom in
Previous page
1/37
Next page
THE DVD PLAYER SETUP MENU
34
DTS
MPEG
PCM CHANNEL
LPCM Out
DUAL MONO
DYNAMIC
Default setting:
SPDIF ( Sony / Phillips Digital InterFace ) refers to the digital
audio format used by most consumer electronics equipment. If
you are using the Stereo Audio Output, change this setting to
. Generally, the setting is used with receivers
capable of Dolby Digital 5.1 or DTS 5.1 channel decoding,
while the setting is reserved for two channel equipment.
Select if you are using stereo audio outputs.
Default setting:
If you are using the Stereo Audio Output, leave this setting at
. Generally, the setting is used with receivers
capable of Dolby Digital 5.1 or DTS 5.1 channel decoding,
while the setting is reserved for two channel equipment.
Select if you are using stereo audio outputs.
Default setting:
When connecting the unit to a receiver capable of supporting a
six speaker system, use this option to configure each pair of
speakers. is used for configuration of the left and
right front speakers. designates configuration
for the left and right satellite speakers.
is for the center speaker and subwoofer.
Default setting:
Select from or for this selection.
Default setting:
These settings are generally for CDs or VCDs that offer only
Mono audio tracks. In this case, the option will
function as normal stereo, while the and
will send the mono output to only one speaker.
will send the same mono output to both speakers.
Default setting:
‘Dynamic Range Compression’ makes watching a movie at
low volumes more enjoyable by boosting the quieter sounds
while suppressing the louder sounds. This reduction in the
difference between the low and high audio levels is known as
“compression”. You can adjust the level of this compression
from to , using the UP/DOWN ARROW buttons.
RAW
PCM RAW
PCM
Off
PCM
PCM RAW
PCM
Off
SPDIF L / R
SPDIF L/R
SPDIF LS/LR
SPDIF C/LFE ( or
subwoofer )
48K
48K 96K
STEREO
STEREO
L-MONO R-MONO
MIX-MONO
Off
OFF FULL
.
Sample Rate
...
Set the sample rate
HDCD Setup Page
..
Off
44.1K
88.2K
Off
HDCD
Default setting:
Choose from two different Khz settings for HDCD.
Off
HDCD SETUP
SOUND PRESET
BASS BOOST
Default setting:
Choose from a variety of equalization presets that simulate
popular environments for listening to music.
Default setting:
When set to , the low frequency range is increased.
Default setting:
When set to , the low frequency range is increased.
Default setting:
When set to , the high frequency range is increased.
NONE
Off
ON
Off
ON
Off
ON
SUPER BASS
TREBLE BOOST
The PASSWORD SETUP PAGE
Video Setup Page
....
Password On
Go To Security Setup Page
Security Setup Page
....
Change Psw
Parental
Off
PASSWORD
Default setting: Off
Here is where you can set an additional password to the default
factory password. The procedures to change an existing
password or enter a new password are the same - you must enter
the OLD PASSWORD, then key in your new password twice to
confirm. If you are entering a new password, or replacing a
password you have forgotten, use the factory default password
of 1379 as the OLD PASSWORD. If you are changing a
previously entered password, you may enter that value as the old
password.
SOUND SETUP
Sound Setup Page
........
Sound Preset
Bass Boost
Super Bass
Treble Boost
None
Off
Off
Off
None
Rock
Pop
Live
Dance
Techno
Classic
Soft
Go to sound setup page
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denver MT-703 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denver MT-703 in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info