555810

Defort DMS-1200-C Manual

13
Zoom out
Zoom in
Previous page
1/32
Next page
13
GB
POSITION OF THE OPERATOR
● Do not stand in a line with the saw blade in front of
the machine. Always stand aside of the saw blade. This
protects your body against possible kickback.
– Keep hands, fi ngers and arms away from the rotating
saw blade.
– Do not cross your arms when operating the tool arm.
CUTTING OFF
– Firmly clamp the workpiece as appropriate for its di-
mensions.
– Adjust the requested horizontal and/or vertical mitre/
bevel angle.
– Switch on the machine.
– Press lever 3 and slowly guide the tool arm down-
ward by handle 1.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade
has come to a complete stop.
– Guide the tool arm slowly upward.
TRANSPORT
Before transporting the power tool, the following steps
must be carried out:
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted
fi rmly to the power tool.
If possible, place unused saw blades in an enclosed
container for transport.
– For lifting or transporting, hold the power tool by the
recessed grips 13 on the side of the saw table 11.
● When transporting the power tool, use only the trans-
port devices and never use the protective devices.
MAINTENANCE AND SERVICE
MAINTENANCE AND CLEANING
● Before any work on the machine itself, pull the mains
plug.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SBM
Group .
CLEANING
For safe and proper working, always keep the power
tool and its ventilation slots clean.
The retracting blade guard must always be able to
move freely and retract automatically. Therefore, al-
ways keep the area around the retracting blade guard
clean.
Remove dust and chips after each working procedure
by blowing out with compressed air or with a brush.
46° (left side) to 46° (right side).
– Release clamping lever, if tightened. This allows the
saw table to move freely.
– Turn the saw table 11 left or right by handle 9 until the
angle indicator indicates the desired mitre angle.
ADJUSTING VERTICAL BEVEL ANGLES
The vertical bevel angle can be set in the range from
0° to 45°.
– Loosen the clamping lever 23.
– Tilt the tool arm by the handle 1 until the angle indica-
tor indicates the desired bevel angle.
– Hold the tool arm in this position and retighten the
clamping lever 23.
For quick and precise setting of the standard angles 0°
und 45°, end stops are provided on the housing.
– Loosen the clamping lever 23.
– For this, tilt the tool arm by the handle 1 to the stop to-
ward the right (0°) or to the stop toward the left (45°).
– Retighten the clamping lever 23 again.
STARTING OPERATION
● Observe correct mains voltage! The voltage of the
power source must agree with the voltage specifi ed
on the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
SWITCHING ON
– To start the machine, press the On/Off switch 19 and
keep it pressed.
Note: For safety reasons, the On/Off switch 19 can-
not be locked; it must remain pressed during the entire
operation.
The tool arm can only be guided downward when
pressing lever 3.
– For sawing, you must additionally press lever 3 in
addition to actuating the On/Off switch.
SWITCHING OFF
– To switch off the machine, release the On/Off switch
19.
WORKING ADVICE
GENERAL SAWING INSTRUCTIONS
● For all cuts, it must fi rst be ensured that the saw
blade at no time can come in contact with the fence,
screw clamps or other machine parts. Remove possibly
mounted auxiliary stops or adjust them accordingly.
Protect the saw blade against impact and shock. Do
not subject the saw blade to lateral pressure. Do not
saw warped/bent workpieces. The workpiece must al-
ways have a straight edge to face against the fence.
Long workpieces must be underlaid or supported at
their free end.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DMS-1200-C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DMS-1200-C in the language / languages: English, German, French as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info