Manual Defort DMS-1200-C (page 12 of 32) (English, German, French)

555810

Zoom out

Zoom in

1/32

– Determine the cause of the blockage and correct it.

INTEGRATED DUST EXTRACTION

– Mount the dust bag 18 onto the sawdust ejector 21.

During sawing, the dust bag must never come into con-

tact with the movable machine parts. Always empty the

dust bag in good time.

EXTERNAL DUST EXTRACTION

For dust extraction, a vacuum hose can also be con-

nected to the dust ejector 21.

The vacuum cleaner must be suitable for the material

being worked. When vacuuming dry dust that is espe-

cially detrimental to health or carcinogenic, use a spe-

cial vacuum cleaner.

CHANGING THE TOOL

● Before any work on the machine itself, pull the mains

plug.

● When mounting the saw blade, wear protective

gloves. Danger of injury when touching the saw blade.

Use only saw blades whose maximum permitted speed

is higher than the no-load speed of the power tool.

Use only saw blades that correspond with the charac-

teristic data given in these operation instructions and

that are tested and marked in accordance with EN

847-1.

Use only saw blades recommended by the tool manu-

facturer, and suitable for sawing the materials to be

cut.

MOUNTING THE SAW BLADE

If required, clean all parts to be mounted prior to as-

sembly.

– Press lever 3, swing back the retracting blade guard

5 to the stop and hold it in this position.

– Place the new saw blade onto the interior clamping

ﬂ ange.

● When mounting the saw blade, pay attention that the

cutting direction of the teeth (arrow direction on the saw

blade) corresponds with the direction of the arrow on

the blade guard!

– Slowly guide the retracting blade guard downward

again.

– Place on the clamping ﬂ ange and the screw.

Press the spindle lock 28 until it engages and tighten

the screw turning in anticlockwise direction.

OPERATION

● Before any work on the machine itself, pull the mains

plug.

ADJUSTING THE CUTTING ANGLE

● When adjusting the cutting angle, never actuate

the On/Off switch 19. Danger of injury if the machine

should accidentally start.

ADJUSTING THE CUTTING ANGLE

● When adjusting the cutting angle, never actuate

the On/Off switch 19. Danger of injury if the machine

should accidentally start.

ADJUSTING HORIZONTAL MITRE ANGLES

The horizontal mitre angle can be set in the range from

FUNCTIONAL DESCRIPTION

Read all safety warnings and all instructions. Failure

to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

INTENDED USE

The power tool is intended as a stationary machine

for making straight lengthways and crossways cuts in

wood. In this, mitre angles from –46° to +46° as well as

bevel angles from 0° to 45° are possible.

The capacity of the power tool is designed for sawing

hardwood and softwood.

The power tool is not suitable for cutting aluminium or

other non-ferrous metals or alloys.

ASSEMBLY

● Avoid unintentional starting of the machine. During

assembly and for all work on the machine, the power

plug must not be connected to the mains supply.

Note: Check the power tool for possible damage. Be-

fore further use of the machine, check that all protective

devices are fully functional. Any lightly damaged parts

must be carefully checked to ensure ﬂ awless opera-

tion of the tool. All parts must be properly mounted and

all conditions fulﬁ lled that ensure faultless operation.

Damaged protective devices and parts must be imme-

diately replaced by an authorised service centre.

MOUNTING TO A WORKING SURFACE

● To ensure safe handling, the machine must be

mounted on a level and stable surface (e. g., work-

bench) prior to using.

– Carefully remove all parts included in the delivery

from their packaging.

– Remove all packaging material from the machine and

the accessories provided.

– Fasten the power tool with suitable screw fasteners

to the working surface. The holes 12 serve for this pur-

pose.

DUST/CHIP EXTRACTION

Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harm-

ful to one’s health. Touching or breathing-in the dusts

can cause allergic reactions and/or lead to respiratory

infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are con-

sidered as carcinogenic, especially in connection

with wood-treatment additives (chromate, wood pre-

servative). Materials containing asbestos may only be

worked by specialists.

– Always use dust extraction.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 ﬁ lter-class respira-

tor.

Observe the relevant regulations in your country for the

materials to be worked.

The dust/chip extraction can be blocked by dust, chips

or workpiece fragments.

– Switch the machine off and pull the mains plug from

the socket outlet.

– Wait until the saw blade has come to a complete

stop.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Defort DMS-1200-C in the language / languages: English, German, French as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Defort DMS-1200-C Manual

Product: