Manual Defort DMS-1200-C (page 11 of 32) (English, German, French)

555810

Zoom out

Zoom in

1/32

that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

● Do not use high speed steel (HSS) saw blades. Such

saw blades can easily break.

● Do not touch the saw blade after working before it

has cooled. The saw blade becomes very hot while

working.

● Never operate the machine without the insert plate.

Replace a defective insert plate. Without ﬂ awless insert

plates, injuries are possible from the saw blade.

● Check the cable regularly and have a damaged cable

repaired only through an authorised customer service

agent for SBM Group. Replace damaged extension ca-

bles. This will ensure that the safety of the power tool

is maintained.

● Store the machine in a safe manner when not being

used. The storage location must be dry and lockable.

This prevents the machine from storage damage, and

from being operated by untrained persons. Secure the

workpiece. A workpiece clamped with clamping devices

or in a vice is held more secure than by hand.

● Never leave the machine before it has come to a

complete stop. Cutting tools that are still running can

cause injuries.

● Never use the machine with a damaged cable. Do

not touch the damaged cable and pull the mains plug

when the cable is damaged while working. Damaged

cables increase the risk of an electric shock. Prod-

ucts sold in GB only: Your product is ﬁ tted with an BS

1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it

should be cut off and an appropriate plug ﬁ tted in its

place by an authorised customer service agent. The

replacement plug should have the same fuse rating as

the original plug.

The severed plug must be disposed of to avoid a pos-

sible shock hazard and should never be inserted into a

mains socket elsewhere.

Products sold in AUS and NZ only: Use a residual cur-

rent device (RCD) with a rated residual current of 30

mA or less.

SYMBOLS

The following symbols can be important for the opera-

tion of your power tool. Please memorise the symbols

and their meanings. The correct interpretation of the

symbols helps you operate the power tool better and

more secure.

Wear a dust respirator.

Wear safety goggles.

Wear ear protectors. Exposure to noise can

cause hearing loss.

Keep hands away from the cutting area while

the machine is running. Danger of injury when

coming in contact with the saw blade.

Danger area! Keep hands, ﬁ ngers or arms

away from this area.

other condition that may affect the power tool’s opera-

tion. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁ ed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

SAFETY WARNINGS FOR CHOP AND MITRE

SAWS

Never make warning signs on the machine unrecog-

nisable.

● Never stand on the power tool. Serious injuries can

occur when the power tool tips over or when inadvert-

ently coming into contact with the saw blade.

● Make sure that the guard operates properly and that

it can move freely. Never lock the guard in place when

opened.

● Never remove cutting remainders, wood chips, etc.

from the sawing area while the machine is running. Al-

ways guide the tool arm back to the neutral position

ﬁ rst and then switch the machine off.

● Guide the saw blade against the workpiece only

when the machine is switched on. Otherwise there is

damage of kickback, when the saw blade becomes

wedged in the workpiece.

● Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

Operate the power tool only when the work area to the

workpiece is clear of any adjusting tools, wood chips,

etc. Small pieces of wood or other objects that come

in contact with the rotating saw blade can strike the

operator with high speed.

● Keep the ﬂ oor free of wood chips and material re-

mainders. You could slip or trip.

● Always ﬁ rmly clamp the piece to be worked. Do not

saw workpieces that are too small to clamp. Otherwise,

the clearance of your hand to the rotating saw blade

is too small.

● Use the machine only for cutting the materials listed

under Intended Use. Otherwise, the machine can be

subject to overload.

● If the saw blade should become jammed, switch the

machine off and hold the workpiece until the saw blade

comes to a complete stop. To prevent kickback, the

workpiece may not be moved until after the machine

has come to a complete stop. Correct the cause for

the jamming of the saw blade before restarting the ma-

chine.

● Do not use dull, cracked, bent or damaged saw

blades. Unsharpened or improperly set saw blades

produce narrow kerf causing excessive friction, blade

binding and kickback.

● Always use saw blades with correct size and shape

(diamond versus round) of arbor holes. Saw blades

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Defort DMS-1200-C in the language / languages: English, German, French as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Defort DMS-1200-C Manual

Product: