481718

De Dietrich Gas 610 ECO Manual

56
Zoom out
Zoom in
Previous page
1/76
Next page
55
De Dietrich Gas 310/610 ECO
13.2.1 Minimum fan speed ( and )
Parameter , adjustable between 06 and 60 (x100 rpm) parameter , adjustable between 0 and 100 (x 1 rpm).
This setting is only active if setting  has been selected in the boiler control: high/low control (see section
13.1.3). The value relates to the percentage output when the boiler is running at ‘low’. The percentage ‘high’
position depends on the set maximum central heating speed.
13.2.2 Maximum fan speed (and )
Parameter adjustable between 10 and 60 (x100 rpm) and parameter adjustable between 0 and 100 (x 1
rpm).The maximum speed can be limited at a lower value in the software by changing parameters and .
Important!! Do not modify these settings, factory settings.
Important!! Only make changes after consulting DDR Americas Inc. support department.
13.2.3 Forced part load time ()
Parameter adjustable between 0 and 300 seconds. The boiler always starts with a specified output for a certain
time. The boiler can then be sent to the minimum position (20% of output) for a specific period, independent of
the heat demand.
13.2.4 Cycling prevention delay time ()
Parameter () adjustable between 0 and 300 seconds. These values set a minimum off time following a control
stop / end of a heat demand to prevent cycling taking place. When, after this delay time flow temperature lies less
than 9°F [5°C] above return temperature (check °n water flow), the boiler will restart.
13.2.5 Required flow temperature at 0 – 10 volts ( and )
Start point (0 volts): parameter , adjustable between -58
and 122°F [-50
°
C and +50
°
C]
This value sets the required flow temperature at 0-volt
signal input. End point (10 volts): parameter ,
adjustable between 124 and 480°F [+51°C and +249°C
this value sets the required flow temperature at 10-volt
signal input (restricted by the maximum flow temperature
set-point and the maximum output).
These settings only apply if boiler control  has been
selected: ‘external analog input 0-10V on the basis of
flow temperature’.
13.2.6 Switch point high/low operation signal ()
Parameter , adjustable between 0 and 60 (x100) rpm. This parameter enables setting the switch point between
“low fire” and “high fire.” A fan speed below the set value will cause a “low fire” signal. A fan speed above the set
value will cause “high fire” signal. A fan speed above the set value will cause a “high fire” signal. An “ON/OFF”
signal can be obtained by setting parameter to 60 = 6000 rpm
13.2.7 Shunt pump post-circulation time ()
Parameter , setting  = 10 sec;  = continuous and adjustable between  and  = number of
minutes.
Continuous water circulation is advisable if there is a danger of the heating system freezing up.
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for De Dietrich Gas 610 ECO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of De Dietrich Gas 610 ECO in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info