585987
14
Zoom out
Zoom in
Previous page
1/20
Next page
Installation Manual Rhino™ 10
10
Attaching the Rhino™ 1
or the Rhino™ 10 to operate, you must provide power from the vehicle DC power supply (12V – 60V) or from an
AC/DC power supply.
ection, so the unit retains power even when the vehicle is
Vehicle Connection
main po
wer connection. Consult your vehicle manufacturer or local representative for the best location to connect to
be disconnected from the Rhino™ 10.
allows for moving the location of the Rhino™ 10 on the vehicle at a
inal. (crimper tool not included)
vehicle chassis.
e end of the fuse holder.
to
0 to Power
F
Positive power sh
ould go to a non-switched conn
off.
For vehicles with 12 to 48 VDC power available, the Rhino™ 10
should be connected directly to the battery or to a
power.
1. First run the cable from the Rhino™ 10 to the power connection location and secure the cable at several
points with wire ties. Leave a little slack at the Rhino™ 10 to allow for mount adjustment and for the cable to
2. Disconnect the power cable from the Rhino™ 10.
3. Either cut off any excess cable or coil the excess cable in a convenient location and secure with wire ties.
Coiling the cable is recommended as it
later date.
4. Strip enough of the outside jacket to allow the positive and negative connections to reach.
5. Strip ¼” from the Black wire and crimp to a correct size wire lug to allow connection to the power source
ground term
6. Strip ¼” from the Brown wire and crimp to a correct size wire lug to allow connection to the
7. Strip ¼” from the Blue wire and from both ends of the fuse holder.
8. Crimp the cable splice onto the Blue wire and on
9. Select the correct size wire lug to allow connection to the positive terminal of the power source and crimp on
the other end of the fuse holder.
10. Connect all wires to the proper source.
11. Connect the cable to the Rhino™ 10. The unit will boot up at this point.
Figure 10 – Power Wiring Diagram
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Datalogic Rhino 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Datalogic Rhino 10 in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Datalogic Rhino 10

Datalogic Rhino 10 User Manual - English - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info