534695

Cubify CubeX Manual

16
Zoom out
Zoom in
Previous page
1/37
Next page
9. When the material jets from the print jet tip, the next screen will ask if you want to
replace another cartridge. If replacing another or adding cartridge, select the print
jet’s material cartridge to be replaced / added and repeat “LOADING MATERIAL
CARTRIDGE” instructions. (Fig. 38)
NOTE: Test creations have been printed on your CubeX before leaving our
factory. A different material and / or color may have been used for the test
creation and may have a small amount of this test material in the print jet.
Therefore, when the material jets for the rst time, the color may be different
until the test material is completely jetted from the print jet and your choice of
material will become visible during this process.
Fig. 35
6. Thread the lament under the cartridge clamp bar and into the feed tube. (Fig. 35)
Fig. 36
7. Install the new cartridge from the side of CubeX and into the cartridge bay. (Fig. 36)
Fig. 37
8. Push lament between the front of cartridge and the eyelet, through the feed tube
and up to the printjet. (Fig. 37)
Fig. 38
10. Once cartridge is installed, press “Next” on the touchscreen. A message “Would you like to load a new Print Jet” will
appear on the touchscreen. If you are adding another cartridge, select the check box and repeat Steps 1-9. Otherwise
select X to return to the main menu.
REPLACING A MATERIAL CARTRIDGE
NOTE: The REPLACE functions will take you through the process of installing the material cartridge.
1. Press REPLACE on the touchscreen and select the bay that the cartridge be
installed. Print Jet 1 represents bay 1, Print Jet 2 represents bay 2 and Print Jet 3
represents bay 3. Press “Next” on the touchscreen, a message “Heating Print Jet
Please Wait…” will appear on the control panel. (Fig. 39)
2. After the print jet is heated, the next message will appear asking to “Gently Pull
Filament From Feed Tube.” Gently pull the lament in between the cartridge front
holder and eyelet as shown. Press “Next” on the touchscreen. (Fig. 40)
Fig. 39
1 2
Fig. 40
15
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cubify CubeX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cubify CubeX in the language / languages: English as an attachment in your email.

The manual is 4,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info