772448
14
Zoom out
Zoom in
Previous page
1/32
Next page
12 CroozerCargo20-ENG-9-19
Preparing the Croozer Cargo for Use as a Bicycle Trailer
3. Fit the axle hitch (3) over the end of the quick-release
skewer without removing the spring.
4. Thread the axle nut (2) back onto the skewer. Tighten
the axle nut at least ve full turns (clockwise).
The axle nut must engage the threads for at least five full
turns in order to ensure adequate clamping force for hold-
ing the rear wheel securely. Failure to tighten the axle nut
adequately may result in accidents with serious injury or
death. If the quick-release skewer is too short, it must be
replaced. Consult a professional bicycle mechanic for the
appropriate parts and assistance.
5. Check that the rear wheel is properly aligned, adjusting
the position if necessary; then close the quick-release
lever (1) or tighten the hex bolt, depending on the ver-
sion. Often, the closed position is indicated on the lever
by the word “CLOSE”. In this case, when the lever side
marked “CLOSE” can be seen, the lever is in the closed
position. If the axle nut has been tightened the proper
amount, you will be able to feel the resistance increase
when the lever is about halfway closed, i.e. parallel to
the axle. The adjustment is correct if you can fully close
the lever but with considerable force. In the closed
position, the lever should be parallel to the frame, i.e. it
should not stick out to the side.
6. Check whether the quick-release skewer is securely
engaged by trying to rotate the quick-release skewer
without opening the lever.
If the quick-release skewer is loose enough to rotate,
then the clamping force is inadequate. In this case,
open the lever, and tighten the tension-adjusting nut
half a turn clockwise. Repeat steps 5 and 6.
If it is impossible to push the quick-release lever into
the closed position, then open the lever, and unscrew
the tension-adjusting nut half a turn anticlockwise.
Repeat steps 5 and 6. Keep in mind that the tension-
adjusting nut must engage the threads of the quick-
release skewer for at least ve full turns.
The tension-adjusting nut must engage the threads for at
least five full turns in order to ensure adequate clamping
force for holding the rear wheel securely. Failure to tighten
the tension-adjusting nut adequately may result in accidents
with serious injury or death. If the quick-release skewer is
too short, it must be replaced. Consult a professional bicycle
mechanic for the appropriate parts and assistance.
Tip: If there is not enough space for mounting the axle
hitch or if the skewer threads are too short, then you
can replace the original skewer with a Croozer Click
& Crooz® Quick Release Skewer with integrated
hitch, which is available as an accessory.
7. Finally, hold the rear wheel with both hands and try to
rock it back and forth to check that the wheel is held
securely in the dropouts.
The rear wheel of the towing bicycle must be properly at-
tached after the axle hitch has been installed. Riding with
an improperly installed rear wheel can result in accidents
with serious injury or death. Follow the instructions given
in the owner’s manual of the towing bicycle.
Accessory
www.croozer.com
www
1
2
3
min. 5 x
3
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Croozer Cargo - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Croozer Cargo - 2020 in the language / languages: English as an attachment in your email.

The manual is 4.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Croozer Cargo - 2020

Croozer Cargo - 2020 User Manual - German - 32 pages

Croozer Cargo - 2020 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info