736873

Crivit ZA-3160 IAN 285955 Manual

15
Zoom out
Zoom in
Previous page
1/44
Next page
15GB/IE
Note: You will need a pump with a standard
connection for the screw valves.
Proceed as follows with both valves:
1. Turn the female thread (3a) on the hose (3)
onto the thread (2a) on the double action
pump (2).
2. Insert the end of the hose (3b) into the valve
(4b).
3. Use the double action pump to pump a
maximum 0.5 bar (7 PSI) of air into the air
chamber (1b).
4. Stop inflating as soon as the manometer
displays 0.5 bar or 7 PSI.
5. Pull the end of the hose out of the valve and
place the valve cover on the valve.
6. Tighten the valve cover (4c) in a clockwise
direction.
Note: If you do not have a manometer then you
can test the correct pressure using your thumb.
Press your thumb on the inflated air chambers.
The product is correctly inflated if it feels firm and
can still be depressed easily with your thumb.
Attachment (fig. D)
1. Attach all the loops (1c) on the tent to the
ground using the tent pegs (5).
Note: Please ensure that the tent pegs are
secured at an angle of 45 degrees.
2. Attach the adjustable loop (1d) on the back
of the tent using a tent peg.
3. Pull on the loose end of the adjustable loop
until it is pulled tight.
4. Pull the ends of the four guy ropes (6) through
the tent loops (1e) and knot them in place.
5. Secure the four guy ropes with one tent peg
each. The length of the guy ropes can be
adjusted using the tightener (6a).
Dismantling (fig. E)
Note: Dismantle the tent in the cleanest and
driest condition possible in order to avoid the
formation of mildew or mould stains.
Dry the tent immediately if it is dismantled in the
rain. Clean all parts thoroughly before packing.
1. Remove all tent pegs (5).
2. Turn the thread (4a) on the valve (4) anti-
clockwise out of the thread opening (1a) in
order to allow the air to escape from the air
chamber (1b).
Folding arrangement
1. First fold the tent lengthwise and then lay the
outer side that is thus formed into the centre.
Important: The folded dimensions must be the
maximum width of the carrying bag.
2. Place the tent pegs and the double action
pump into the relevant bags (8) (9).
3. Place the bag (9) with the double action
pump on one end of the tent and then roll it
up.
Note: Please ensure that the folded tent is rolled
towards the end with the opened valve.
4. Lay the folded tent and the bag with the tent
pegs into the carrying bag (10) and close it.
Repair, care and storage
Repair
Small leaks or holes can be repaired with the
included repair patches (7).
Important! Do not inflate the product
for 20 minutes after repair!
Do not use the patches on the seam.
- Allow the air to escape from the product
completely.
- Clean the area around the leak thoroughly!
The area must be dry and free of grease.
- Remove the patch from the paper, place it on
the damaged area, and press it down firmly.
If the valve (4) is defective then you can replace
it with the replacement valve. In order to do this,
proceed as shown in fig. F.
Care
Brush off soiling on the tent skin when dry; clean
off with clear water if necessary. Do not use
chemical cleaning agents. You should seal the
tent seams from time to time. Use standard seam
sealants for this purpose.
Tent:
Carrying bag:
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit ZA-3160 IAN 285955 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit ZA-3160 IAN 285955 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info