736873

Crivit ZA-3160 IAN 285955 Manual

14
Zoom out
Zoom in
Previous page
1/44
Next page
14
• Small leaks at the seams can be fixed with a
seam spray and impregnating spray can be
used for the tent skin.
Precautionary measures
against fire
The following common sense rules must
be followed to ensure safe camping:
• Do not position any active electronic devices
close to the walls, roof, or curtains.
• Always observe the safety instructions for
these devices.
• Never allow children to play near active
devices.
• Leave passageways free. Do not block the
exits with objects.
• Ask about the fire safety facilities and arrange-
ments on the site.
Assembly
Note: Carry out a trial assembly before starting
your journey. Make sure that all the accessories
are in place.
Selecting the assembly location
Choose the most level, clean assembly location
possible. Avoid dips in the ground.
Remove stones, branches, and other pointed
objects in order to prevent damage to the floor
of the tent. Use natural lee sites with hedges,
rocks etc.
Use the right tent pegs for sandy ground in order
to avoid the guy ropes coming loose.
Note: Insert the tent pegs into the ground at a
slight angle so that good grip is achieved but no
tension is created in the tent skin. The tent material
and the suspension points should only be under
slight tension so that wind loads can be offset.
Please ensure that the product is not subjected to
too much tension. Check the tent tension depen-
ding on the weather.
Note: Condensation will happen in all tents in
principle but it will be particularly prominent if
there are large changes in temperature. There
will be drops of condensation on the inner wall
after a night in the tent. Therefore condensation
is not a sign of leaks. Good ventilation will redu-
ce condensation inside the tent.
1. Spread the tent (1) out flat on the surface.
2. Turn the thread (4a) on the valve (4) in a
clockwise direction tightly into the thread
opening (1a) on the tent (1) (fig. B).
ATTENTION!
• The recommended operating pressure is
0.5 bar (7 PSI).
• Avoid over-inflation as this could lead to
the risk of overstretching or even tearing the
welded seams.
• Use standard foot pumps or double action
pumps with corresponding attachment options
to inflate the product, if necessary with a
manometer.
• Do not use a compressors or bottles of com-
pressed air to inflate the product.
This can lead to damage.
• Always inflate the product completely.
• Do not inflate the product in the vicinity of
pointed or sharp objects or on rough or gra-
velly surfaces.
Inflation (fig. C)
IMPORTANT!
• The area around the valves must
always be dry and clean.
• Please ensure that no sand or other
contaminants get into the valves.
• Avoid over-inflation of the air cham-
bers as this could bring with it the risk
of overstretching or of the welded
seams tearing.
• Use the included double action pump
to inflate the product. Otherwise only
use standard foot pumps or double
action pumps with corresponding
pump adaptors.
• Do not use a compressor or bottles of
compressed air to inflate the product.
This can lead to damage to the product.
• Please ensure that the air chambers
are inflated evenly.
• Only inflate the air chambers until
they feel firm. It should be possible to
depress the air chamber easily if you
press against it with your thumb.
GB/IE
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit ZA-3160 IAN 285955 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit ZA-3160 IAN 285955 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info