Manual Crivit IAN 304198 (page 19 of 76) (English, German, Dutch, French, Portuguese, Spanish)

736211

Zoom out

Zoom in

1/76

23GB/IE

Danger!

• Handle damaged or leaking batteries with

extreme caution and dispose of them properly

as soon as possible. Wear gloves when doing

so.

• If you come into contact with battery acid, wash

the affected area with soap and water. If battery

acid gets in your eye, rinse it with water and

seek medical attention immediately!

• The connection terminals must not be short-circuit-

ed.

Replacing the batteries

CAUTION! Observe the following instruc-

tions to avoid mechanical and electrical

damage.

Danger!

There is a battery LR03 in the item. You can replace

the battery if it stops working.

1. Raise the display on the side, and carefully re-

move it. The battery is at the back of the display.

2. Slide the battery carefully out of the battery

casing and replace with a new one.

Note: Make sure that the battery is inserted prop-

erly and completely in its casing.

3. Insert the display and the cable connections into

the casing once again.

Note: Make sure that the display is correctly

inserted in the casing once again.

Assembling the stepper

Step 1:

Insert both plastic feet into the pipe on the back of

the frame. The ribbed contact surfaces lie on the

floor and the sharp ends point backward (Fig. C).

To anchor it, a self-tapping screw is inserted into the

pre-drilled hole on the underside of the frame.

Note: Make sure that the pre-drilled hole in the

frame and the plastic foot are placed exactly on

top of each other.

Step 2:

The adjustable screw is screwed into the thread on

the front of the stepper.

With the help of this screw, you may adjust the step

height of the tread surfaces.

To increase the step height, turn the adjustable

screw in a clockwise direction. To lower the step

height, turn the adjustable screw in an anticlock-

wise direction.

Step 3:

Remove the computer from the stepper by pulling

it upwards.

Place the supplied battery in its appropriate com-

partment on the underside of the computer. Ensure

that the polarities are correctly aligned.

Connect the computer to the connector on the

casing and insert it once again. Make sure that the

cable does not get pinched during this procedure.

Step 4:

Observe the maximum stretch length of

the straps.

The shorter the straps, the greater the effort expend-

ed.

• Shorten the straps by locking the rubber hose

with the safety ball into place (Fig. B).

IMPORTANT! Make sure not to shorten

the straps too far. Do not go past the

“MIN.” marking!

• Hook the metal hook into the eyelet on the step-

per frame and screw in the fastener on the hook

tightly (Fig. D).

Important! Before training, check that

the straps are securely fitted, and that

the hook is safely and tightly screwed

in. Caution! The eyelets are secured for

tensile loads upwards only, and may not

be subjected to transverse loads. There is

a risk of injury, or damage to the stepper.

When you are not training with the straps, unhook

them from the eyelets to avoid tripping over them.

Check whether all screws and nuts are securely

tightened.

Operating the computer

The stepper meets accuracy grade C, i.e., there is

no claim to accuracy in the computer displays.

Turning the item on and off

When you start exercising or operating the pedals,

the computer switches on automatically. If the

stepper is out of operation for approx. 4 minutes,

the computer switches off automatically.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 304198 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit IAN 304198 Manual

Product: