732011

Crivit 1-LD4657 - IAN 285498 Manual

17
Zoom out
Zoom in
Previous page
1/72
Next page
-
31
-
Incorrectly performing the calibration can
result in faulty measurements. When
encountering "suspicious" or incorrect
readings, the calibration should be
repeated.
Entering the deviation (declination) to the
geographical North Pole
This deviation results from the calculable
difference between the magnetic North Pole
and the geographical North Pole as used
on maps. The local deviation is printed on the border of geographical maps (the
deviation depends on the latitude). It is shown as a positive east value (E) or a
negative west value (W). When using the map to navigate to a target, the direction
to the target must be adjusted on the map. This is done by subtracting the positive
value or adding the negative value to the shown value.
Press and hold SET to enter the declination mode.
Immediately after entering the setting mode for the
declination, the letter "E" (for east) will blink on the display. Press SEL to select E or
W (for west). Press SET to confirm your selection.
The degree digits will blink on the display. Press SEL to enter the declination and
press SET to confirm your setting.
Because the entered values directly influence the directional indication, they must be
activated by pressing SEL to select " ON" or „ OFF“. Confirm your selection by
pressing SET.
Exit setting mode by pressing MODE.
The following examples may help to explain the effect of the deviation:
The direction shown on the display is N10° (10 degress north).
Entering an east deviation (E) of 30 degrees will change the directional indication to
NE (north-east) 40 degrees.
Entering a west deviation (W) of 30 degrees will change the directional indication
to NW (north-west) 340 degrees.
-
32
-
Altimeter (ALTI)
(-999 m - +9999 m / -2999 ft - +29999 ft)
Please note:
Your altitude is determined by measuring
atmospheric air pressure. The shown value can vary by up to
50 m because of changing weather- regardless of a change
in location.
We recommend that, before use, the altitude value should be
set with the sports watch on your wrist. Then wait for a few
minutes so that the value can stabilize.
Select the feature by pressing MODE repeatedly. Press SEL to select the different
sub-features.
Altimeter (ALTI) > maximum altitude memory (HIGH) > minimum altitude memory
(LOW) > total altitude gain (UP) > total altitude loss (DOWN) > number of hills
(HILL) > memory (RECORD).
Height
Press SEL to select the sub-feature (ALTI).
Press and hold SET for 3 seconds to enter setting mode. Enter the
desired value by pressing SEL and confirm your setting by pressing
SET.
Exit setting mode by pressing MODE.
Press SET to select the display mode height/time or
temperature/time/diagram/current altitude.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit 1-LD4657 - IAN 285498 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit 1-LD4657 - IAN 285498 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info