618062
10
Zoom out
Zoom in
Previous page
1/42
Next page
167
IIt is recommended that before diving at altitude, wait at least
three hours after arriving at your diving destination. This will
allow a partial release of the residual nitrogen from the body.
The atmospheric pressure at higher altitudes is lower than at
sea level. Therefore, the diver has additional nitrogen in his
body than at the lower altitudes. The excess is gradually
released and the balance re-established within a couple of
days. At this point it is important to check:
The low battery indicator. It should not be on or flashing (pic-
ture 2 a-b).
The computer display is operating. All liquid crystal segments
should be displaying.
WARNING: Should the display show the symbol of a low
battery (picture 2 a-b), the computer must NOT be used.
Additionally, should it display during a dive, the diver must
immediately surface. A battery replacement is required as
outlined in chapter 5.
2.3. - PARAMETERS SETTING.
In order to set the dive’s parameters, you must depress the
central button B (Mode), and the icon relating to the
program
you want to use will be shown (picture.3): , for air dives
( ) or Nitrox, mixture(s), or if you want to use
the depth meter /timer program.
NOTE: Archimedes II computer is preset on pro-
gram.
2.3.1. - DIVE program parameters setting.
NOTE: Archimedes II computer is preset on pro-
gram.
This is the basic program with which the Archimedes II is set.
It is possible to modify its parameters by repeatedly depres-
sing button A ( ), which allows you to select, in the following
order, the dive’s parameters relating to:
PO2 Mix 1 -> FO2 Mix 1 -> PO2 Mix 2 -> FO2 Mix 2
-> Safety Factor -> Max Depth -> OFF/ON -> DIVE
that is:
• PO2 Mix 1 is the partial pressure of the former of the two
Nitrox mixtures, so that Archimedes II can make its decom-
pression computations. The diver can set it on values
between 1.0 bar (included) and 1.6 bar (included), by varia-
tions of 0.1 bar, obtained at each pressure of button C ( );
NOTE: By varying of max PO2 setting (picture 3), the com-
puter also indicates the maximum depth (MAX) that may be
reached with that mixture.
WARNING: Both mixtures’ PO2 factory set on a basic value
(default) of 1.4 bar, both for air dives and for Nitrox mixture
dives. The diver is then following the most conservative
values recommended for sport dives. Different PO2 values
may be set as shown in chapter 3.3. The set value will be
memorized in the computer until the diver chooses another
setting.
i
ENGLISH
Manuale ARCHIMEDE II 2008:Manuale 6 26-06-2008 8:26 Pagina 167
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cressi Archimede II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cressi Archimede II in the language / languages: English as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info