768916
5
Zoom out
Zoom in
Previous page
1/31
Next page
8 - erecting the carrycot - stage 1
Remove the mattress and liner from the cot (a). (The liner is retained by a strip of Velcro® at the top).
Open the lining at the base of the cot and slide the frame bars, using the straps (b), until the ‘V
sections on the frame bars fit into the cutouts in the cot base (c).
Reattach the Velcro® strip to complete the step.
9 - erecting the carrycot - stage 2
Refit the liner into the carrycot and secure with the Velcro® strips at the top.
Place the mattress over the liner at the base of the carrycot.
10 - fitting and using the carry handle
To fit the carry handle push each end into the carrycot mountings until the buttons lock the handle
in place (a).
To open the carry handle press the button on one side of the handle (b) and lift the handle end
clear of the mounting (c).
Repeat this procedure at the other end of the handle to remove the handle from the carrycot.
11 - fitting the carrycot
Place the carrycot on to the mounting points on each side of the chassis (a). Push down until the
tab locate in the holes of the carrycot mountings (b).
Note: The carrycot can only be fitted rearward facing as shown in illustration. Dots are marked on
the seat mounts and carrycot mounts (c). These should be on the same side and aligned if fitted
correctly.
There are a set of “D” ring located at the base of the carrycot for the attachment of a separate
safety harness approved to BS EN 13210 should this be required (harness not supplied). Push the
‘D’ rings through the lots in the liner (d).
12 - removing the carrycot
To remove the carrycot from the chassis, press the buttons on each side of the mountings (a) then
lift the carrycot free (b).
Note: Please ensure that the carry handle is securely fitted before lifting the carrycot clear of the chassis.
13 - opening and closing the carrycot hood
Pull the hood up to open (a). Push the hood back down to close (b).
14 - removing the carrycot hood
To remove the carrycot hood, pull the lip at the bottom of the hood mount (a) and pull the hood away.
To re-fit the hood place the top of the hood mount (b) over the chassis frame and then push hard
on the bottom (c) until the hood mount clips in place. Attach the Velcro® tabs (d) on both sides.
15 - fitting the carrycot apron
Lay the cot apron over the carrycot and attach the zip to the liner (a). Pull the zip around the cover
until secure. Place the bib of the cot apron inside of the hood on either side of the hood as shown (b).
Removal of the cover is a reversal of this procedure.
16 - fitting the raincover in pram mode
Fit the raincover over carrycot as shown. The air holes in the raincover should be just in front of the
hood on either side (a).
The cutouts in the raincover fit over the carrycot mounts. Secure with the Velcro® straps (b).
17 - fitting and removing the seat unit
Place the seat unit on to the mounting points on each side of the chassis. Push down until the
tabs locate in the holes of the seat mountings (a).
To remove the seat unit from the chassis, press the buttons on each side of the mountings (b) then
lift the seat unit free (c).
Note:
The seat unit can be fitted facing forwards or backwards.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cosatto Giggle 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cosatto Giggle 2 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info