511355

Constructa CD22130 Manual

38
Zoom out
Zoom in
Previous page
1/56
Next page
38
Important: If the door of the unit is at a
distance from the body of the unit (e.g. due
to rubber stops), the extractor hood must
be drawn forward by the same distance.
7. Mark the position of the lower fixing
screws, predrill and fasten the screws.
8. All four fixing screws must be firmly
tightened.
9. Connect pipes.
10. Connect electricity.
Mounting the door:
Door thickness: min. 16 mm
Door height: 380 to 700 mm
Door weight: 7 kg (max.)
In order to match the wall cabinets on either
side, the door can project at the top and
bottom.
1. Remove the two door carriers to the
right and left, by pulling both the red pla-
stic catches inwards and removing the
door carrier out towards you.
2. Mark the fixing points on the door. For
dimensions of vertical screw fixings, see:
If the top edge of the door is not flush with
the top edge of the cabinet, amend the
dimensions accordingly.
If the tops of the cabinets are not installed
flush with each other, the door must be
mounted correspondingly higher.
The screw locations on the door can be
marked directly on the door in situ. If you
are doing this, leave the door carriers in the
appliance. Position the door, align it and
mark the back.
min.
38
0
max.
700
600
max.
7
kg
1.
2.
+
41
250
570
285
285
2
Keep precisely to the dimension 570 ± 2.
3. Screw the door carriers to the door,
making sure your left-right orientation is
correct.
4. Insert the complete door into the extrac-
tor hood
Check that the door meets the stops on
both sides when pulled out. This means
that it is safely locked in place.
ṇ The red plastic catches can only be
released if the door is not swung out to the
stop.
5. The two screws to the right and left insi-
de the housing can be used to adjust door
gliding according to the weight of the door.
Turning the screws clockwise will make the
door more difficult to move.
Mounting wall covering rail:
The gap between the hood and the rear wall
can be dressed with the enclosed covering rail.
Screw-fasten the covering rail to the under-
side of the extractor hood.
Refit the grease filter.
If the unit door has to be removed:
Pull the red plastic catches in the housing
on both sides inwards to release the door,
which can then be pulled out towards you.
Weight in kg
We reserve the right to construction changes within the
context of technical development.
+
1.
2.
Appliance version
Exhaust air
Recirculating
air
single motor 6,5 7,8
dual motor 8,0 9,3
Installation
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Constructa CD22130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Constructa CD22130 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 9,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info