652338
72
Zoom out
Zoom in
Previous page
1/80
Next page
72 Fault elimination
Code Message Information
Warning Fault Possible causes Remedy
––– E47 Invalid Level Invalid level detected, humidication is stopped!
Note: As soon as the level is within the valid range again, the Condair RS con-
tinuous normal operation.
Magnetic eld in vicinity of level unit. Eliminate magnetic eld.
Level unit defective. Replace level unit
––– E52 ** Unstable Level Unstable level detected, humidication is stopped
Check hose connections between level
unit and steam cylinder receptacle and
between level unit and steam outlet
hose.
Check/clean hose connections, clean
if necessary.
––– E56 Int. Safety Loop Internal safety loop interrupted, humidication is stopped!
Note: As soon as the internal safety loop is closed again, the Condair RS
continuous normal operation.
Connection between heating cable
plug and electronic interrupted.
Let have the heating cable plug and
cable connections to heating cable
plug socket be checked by an electri-
cian.
––– E57 Activation Activation code has not been entered yet.
Activation code has not been entered
yet.
Enter activation code (code available
from your Condair representative).
––– E58 No Water Pressure Not implemented yet.
––– –––
E60, E61,
E62, E73
––– See malfunction list in the Condair RO-A installation and operation manual.
––– E74 ** Keep Alive Communication between control board and driver board interrupted.
Driver board not connected. Correctly connect driver board.
Wrong driver board installed. Install and connect correct driver board.
Driver board defective. Replace driver board.
E80 USB Logger USB data logger fault.
USB data logger not connected or
defective.
Check/replace USB data logger.
––– E82 ** Driver Missing Communication with driver board interrupted.
RS485 Bus to driver board interrupted. Contact your Condair representative.
––– E83 ** Slave Address The driver board of the slave unit has a wrong address. The control can not
differ between Master and Slave.
Rotary switch on the driver board of the
slave unit set wrong.
Set rotary switch on the driver board of
the slave unit to position "1".
––– E84 ** Driver defective Unknown fault on driver board
Driver board defective. Let have the driver board be replaced
by an electrician.
––– E85 ** Driver ID wrong Driver board ID wrong.
Wrong driver board connected or SAB
address wrong.
Contact your Condair representative.
––– E86 ** Driver Incompatible Wrong version of driver board.
Wrong version of driver board. Contact your Condair representative.
––– E87 ** Local 24VSupply Local 24V voltage on driver board out of valid range!
Short circuit on supply module or supply
module defective.
Contact your Condair representative.
––– E88 ** Local 5V Supply Local 5V voltage on driver board out of valid range!
Short circuit on supply module or supply
module defective.
Contact your Condair representative.
––– E89 ** Local Ref Supply Local reference voltage out of valid range!
DC supply faulty or supply line inter-
rupted.
Contact your Condair representative.
E90 –––
See malfunction list in the Condair RO-A installation and operation manual.
72


Need help? Post your question in this forum.

Forumrules
1

Forum

condair-rs

Reset search

  • why drain hose led to left, is it due to electrical on right side.
    Submitted on 29-8-2022 at 23:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair RS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair RS in the language / languages: English as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Condair RS

Condair RS Installation Guide - English - 80 pages

Condair RS User Manual - Dutch - 80 pages

Condair RS Installation Guide - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info