535645
11
Zoom out
Zoom in
Previous page
1/38
Next page
Page 11
800 Series
SECTION 3: CONFIGURATION
Setting The Vend Price On
A Single-Price Changer
The vend price on a single-price changer may
be set in four ways:
via Coinco Support Software
via DEX/UCS
via the first eight Option Switches
via the digital display.
The vend price can be set in single increments
up to 255 times the lowest denomination coin
that is accepted by the changer and routed to a
coin tube.
EXAMPLE: If the lowest denomination coin is
one, the highest vend price setting would be 255
x 1 or 255.
VIA COINCO SUPPORT SOFTWARE
Consult Coinco Support Software manual for
price setting instructions.
VIA DEX/UCS
Consult Hand-held Computer manufacturer.
VIA OPTION SWITCHES
Note: The switches are ON in the upwards
position.
1. Set the vend price by adding the amount of
the appropriate switches and setting them to
the ON position (see Figure 11).
2. Set Option Switch B to the OFF position.
3. Set Option Switches A, C and D to the
desired configuration (see “Option Switch
Module” section of this manual).
4. After setting the vend price and the desired
options, press and release the Mode Button
to store the new setting. The LED and the
“Use Correct Change” light will then flash
once, indicating that the price was recorded.
Figure 11
Example: Switch 1, 3, 4, set to on and the
remaining set to off would result in a price of
(1+4+8) x Scaling Factor. If the scaling factor
were set to 5 and the decimal point set to 2, the
resulting price setting would be (1+4+8) x (.05) =
13 x .05 = 0.65 units. The current scaling factor
can be displayed using display mode, address
“A010” on the acceptor. The current decimal
point position can be displayed using diplay mode,
address “A011”.
NOTE: The vend price must be set to an
amount greater than zero for the changer to
accept coins in single-price mode.
VIA DIGITAL DISPLAY
1. Enter the Display Mode (see “Display
Mode” section of this manual).
2. Press B to scroll up to “C001” (Price 1).
3. Press C to enter. The current Price Setting is
displayed.
4. Use buttons B (increase) and D (decrease) to
change C001 to the appropriate price.
5. Press A to store price and return to the
Display Mode.
7. Press A to exit the diplay mode.
Note: The Display Mode will exit automatically
if there is no programming action for 30
seconds.
Switch 1 ...................................1 x Scaling Factor
Switch 2 ...................................2 x Scaling Factor
Switch 3 ...................................4 x Scaling Factor
Switch 4 ...................................8 x Scaling Factor
Switch 5 .................................16 x Scaling Factor
Switch 6 .................................32 x Scaling Factor
Switch 7 .................................64 x Scaling Factor
Switch 8 ............................... 128 x Scaling Factor
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Coinco Global 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Coinco Global 2 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info