535645
12
Zoom out
Zoom in
Previous page
1/38
Next page
Page 12 800 Series
SECTION 3: CONFIGURATION
5. Within 30 seconds, press and release any one
desired product selection switch on the front
of the machine. The present price on the
switch module is now set for all selections
on that price line and the LED and “Use
Correct Change” light will stop flashing.
6. Repeat the above steps until the remaining
three price lines have been assigned a vend
price.
EXAMPLE: If the first, fourth and fifth price
setting switches are in the UP position, the vend
price setting would be 25 x 1 or 25 (assuming
the lowest denomination coin accepted is 1).
NOTE: If the price for one or more of the
selections is set to zero, that selection is a free
vend.
VIA DIGITAL DISPLAY
1. Enter the Display Mode (see “Display
Mode” section of this manual).
2. Press B to scroll up to C001 (Price 1).
3. Press C to enter. The current price setting is
displayed.
4. Use buttons B (increase) and D (decrease) to
change C001 to the appropriate price.
5. Press A to set the price and return to the
Display Mode.
6. Press B to increase to the next priceline -
E.g. Address C002 (Priceline 2).
7. Repeat steps 3-6 for the remaining three
prices.
8. Once all four prices have been set, press A
twice to exit the Display Mode.
Setting The Vend Price On
A Four-Price Changer
The vend price on a four-price changer may be
set in four ways:
via Coinco Support Software;
via DEX/UCS;
via the first eight Option Switches;
via the digital display.
The vend price can be set in single increments
up to 255 times the lowest denomination coin
that is accepted by the changer and routed to a
coin tube.
EXAMPLE: If the lowest denomination coin is
one, the highest vend price setting would be 255
x 1 or 255.
VIA COINCO SUPPORT SOFTWARE
Consult Coinco Support Software manual for
price setting instructions.
VIA DEX/UCS
Consult Hand-held Computer manufacturer.
VIA OPTION SWITCHES
Note: The swiches are ON in the upwards
position.
1. To set the vend price of a selection, add the
value of the rocker switches that are
switched to the ON position (see Figure 11).
2. Set Option Switch B to the ON position.
3. Set Option Switches A, C and D to the
desired configuration (see “Option Switch
Module” section of this manual).
4. After setting the desired vend price on the
Option Switch Module, press and release the
Mode Button (see Figure 2). The changer’s
Main Logic Board LED and the “Use Cor-
rect Change” light will begin to flash.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Coinco Global 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Coinco Global 2 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info