535645
9
Zoom out
Zoom in
Previous page
1/38
Next page
Page 9
800 Series
SECTION 3: CONFIGURATION
Display Mode
The 800 Series changer is equipped with a
four-digit, seven-segment display, located on
the acceptor gate. The Display Mode is utilized
via the four Inventory Buttons also located on
the acceptor gate (see Figure 9).
This Display Mode is used to read information
as well as to set different options including
price settings and tube float levels.
The Display Mode may be entered by pressing
Inventory Buttons A and D simultaneously. In
response, the display will turn on the message
“FILL”, “FULL”, or “AbCd”. Button activa-
tion will be recognized only if longer than 0.5
seconds. Once you have entered the Display
Mode, Inventory Buttons A through D are used
to move through the addresses as follows:
Button
A .......................................... ESCAPE
Button B...................................... INCREASE
Button C............................................. ENTER
Button D .................................... DECREASE
EXAMPLE: Simultaneously press A and D to
enter Display Mode. Press B to increase
(scroll) through the various addresses. Once
you have reached the address you need to
access, press Button C to enter the address.
Information currently stored in non-volatile
memory will be displayed with the far right
decimal point illuminated. Use either Inventory
Buttons B or D to increase or decrease the
address values as needed. Press Button C again
to store the selection. Press A to return to the
Address Display. Press A again to exit the
Display Mode.
You will exit the Display Mode if one of the
following procedures is performed:
1. No Inventory Buttons are pressed or coins
are dropped for more than 45 seconds;
2. Depressing the A Button until the Display
Mode is exited;
3. Automatic exit after hardware reset.
Figure 9
NOTE: All addresses in the Display Mode can
be made “Read Only” (disabled) via Coinco
Support Software (see separate Coinco Support
software manual for further information).
NOTE: If power is removed from the changer
before the Display Mode is exited, the changes
may not be saved.
Figure 10
Indicates (By A Flash) Each
Changer/Acceptor Communication
Indicates At Least One Coin Is Enabled
Indicates Float Level Is Set On
At Least One Tube
Indicates Power
is ON
DIGITAL DISPLAY
(Normal Operating State)
8 8 8 8
800 Series Changer
DIGITAL DISPLAY
A B C D
Digital Display
Inventory Buttons
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Coinco Global 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Coinco Global 2 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info