468917

Clifford Concept 50 Manual

9
Zoom out
Zoom in
Previous page
1/23
Next page
Built-in vehicle recovery/anti-carjacking circuitry
Concept 50’s built-in BlackJax circuitry provides a safe and effective means of
recovering your vehicle after a theft or carjacking.
IMPORTANT: The factory setting for this feature is OFF. Once you are familiar with
the following, we suggest you turn this feature ON (see pages 20–22). When
anti-carjacking is on, each time you begin driving you MUST enter your disarm-
ing code as noted below (unless the system is in valet mode).
Your secret disarming code tells the system that the car is being driven by an authorized
person. Also, if you open your car door at any point (as would occur in a carjacking
attempt), you must again enter your secret code. Entering your code is simple and easy.
Definitions
Digit: A digit is defined as any number from 1 to 9, inclusive.
Disarming code: A disarming code may be 1 to 3 digits:
A one-digit code = X = any number between 1-9
A two-digit code = XY = any number between 11-99 (excluding numbers with zeros)
A three-digit code = XYZ = any number between 111-999 (excluding numbers
with zeros)
Remember, no code can have a zero.
PlainView switch: A rocker switch mounted on the dashboard or console. The
switch has three positions: 1.) Latched 2.) Center 3.) Spring-loaded momentary.
When you press the latched side, the switch remains in its pressed position. When
you press the momentary side, the switch bounces back to the center position.
Each time you drive your car, you must enter your secret disarming code via the
PlainView switch.
Entering a digit: To enter a digit, you tap (press and release) on the momentary
side of the PlainView switch the number of times corresponding to the numeral of
the digit to be entered, followed by pressing to the latched side, then returning the
switch to its center position.
Entering a code: If your code has only one digit, enter the code as described in
“Entering a digit,” then return the switch to its center position. If your code has
more than one digit, just repeat the above for each digit of your code, then return
the switch to its center position.
Your secret disarming code
Unless the system is in valet mode (see page 13), within 20 seconds after you switch on
the ignition and press the brake (or open a door while the engine is running), you must
enter your secret disarming code to let the system know it is you who is driving. Your
code will be a 1-to-3-digit number of your choosing. Each digit can be any number from
1 to 9, (i.e. the code can be any number between 1 and 999, except those that contain a
zero).
Currently, your system’s factory-set disarming code is the single digit “2.”
7
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clifford Concept 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clifford Concept 50 in the language / languages: English as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info