Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these setting.
✱
WARNING:
If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING; it requires installer-only adjustment. Changing the duration may cause damage.
NOTE 1:Transmit channel 1 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
NOTE 2:Transmit channel 2 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
NOTE 3:Transmit channel 3 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
NOTE 4:Transmit channel 4 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
NOTE 5:Transmit channel 5 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
NOTE 6:When you hear the two chirps, all remote control codes will have been erased from
system memory. You must now add the new and/or existing remote controls to the system
(i.e., program channels 1–5 of each remote that will be used with your Concept 50).
NOTE 7:Turn off the ignition, exit the vehicle (taking the keys with you) and close the doors.
Firmly “thump” the window pillar with the side of your fist. You should hear a chirp to
confirm activation of the sensor’s main zone. Use remote control button 2 to increase
sensitivity, button 4 to decrease. Repeat until the sensor is set to the sensitivity you wish,
then press remote control button 1 to end programming mode.
NOTE 8:Use the same procedure as NOTE 7, but strike the window pillar lightly.
NOTE 9:Use the same procedure as NOTE 7, but firmly tap a coin (such as a quarter) against
the window to test sensitivity.
NOTE 10:Transmit the first channel of your choice (any channel from 1–12). You will hear a
one-chirp confirmation. Transmit the second channel of your choice (again, any channel you
wish from 1–12). You will hear a two-chirp confirmation. You may now use this
combination to turn off the 20-second anti-carjacking countdown.
NOTE 11:Transmit the channel of your choice on the dedicated anti-carjacking remote
control. You will hear two chirps to indicate that that remote control button will now turn
off the 20-second anti-carjacking countdown. Be sure to carry this remote on your person,
since a carjacker will undoubtedly take your usual remote control and purse.
NOTE 12:Immediately flip the switch to its latched position, then enter the new code that
you wish to use. Make sure to return the switch to its center position when complete, then
wait 3 seconds (you will hear two chirps when the system has accepted the new code). Turn
the ignition off. VERY IMPORTANT:You must immediately test your new secret
disarming/valet code: Turn the ignition on, enter your new code, then flip the switch to its
latched position. The LED will illuminate. If it does not, the new code you programmed and
the one you just entered do not match. The system has reverted to the previous code.
NOTE 13:The timer starts as soon as you enable this feature (6 latches, 1 momentary). When
the duration you wish has been reached, press button 1 on the remote control. You will hear two
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Clifford Concept 50 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Clifford Concept 50 in the language / languages: English as an attachment in your email.
The manual is 0,11 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
