684041
71
Zoom out
Zoom in
Previous page
1/80
Next page
71
Warning Error Cause Remedy
Code Malfunction Code Malfunction
W23 No electrode current
for more than 20
minutes
E23 No electrode cur-
rent for more than
4 hours
Phase failure heating voltage. Inspect/turn on service switch of
the mains supply line. Inspect the
fuses of the mains supply, replace
if necessary.
Water supply obstructed/shutoff valve
closed/water pressure too low.
Inspect water supply (filter, water
piping, etc.), check/open shutoff
valve, check water pressure.
Inlet valve blocked or defective. Inspect strainer insert of the inlet
valve, if applicable clean strainer
insert or replace inlet valve.
Excessive back pressure in the steam
line (duct pressure too high, steam
line too long or kinked), causing water
loss via lling cup.
Check duct pressure, inspect s
team
installation. If applicable install
pressure compensation kit (see
options).
Leakage in the water system. Inspect water system and seal if
necessary.
W24 Electrode current in
relation to the steam
demand too high
E24 Electrode current in
relation to the steam
demand too high
Steam demand has decreased too
fast.
Automatic adaptation of the
operating point.
Drain valve defective.
Inspect drain valve, replace if
necessary.
Drain screen in the drain outlet of the
steam cylinder clogged.
Clean drain screen (see chapter 7.3.2
and 7.4) or replace steam cylinder.
Water conductivity too high for this
type of steam cylinder.
Select correct steam cylinder type.
W25 Max. admissible
electrode
current exceeded
E25 Max. admissible
electrode
current exceeded
Drain valve defective.
Inspect drain valve, replace if
necessary.
Drain screen in the drain outlet of the
steam cylinder clogged.
Clean drain screen (see chapter 7.3.2
and 7.4) or replace steam cylinder.
Water conductivity too high for this
type of steam cylinder.
Select correct steam cylinder type.
––– ––– E26 Main contactor
jammed
Main contactor jammed in activated
position.
Inspect main contactor, replace if
necessary.
W27 Foam detection E27 Foam detection (4
automatic drainings
within 24 hours)
Foaming in steam cylinder. Drain steam cylinder via drain key
(several times, if necessary). Check
quality of the supply water.
W28 Steam cylinder
needs service
E28 Service interval for
steam cylinder
exceeded
Mineral deposits and/or electrodes
spent.
Replace steam cylinder.
Important: After the replacement
of the steam cylinder, reset the
maintenance counter (see chapter
7.6).
W29 Steam cylinder
needs service
E29 Max. operating
hours of the steam
cylinder reached
Maximum operating hours of the
steam cylinder reached.
Replace steam cylinder.
Important: After the replacement
of the steam cylinder, reset the
maintenance counter (see chapter
7.6).
W36 Standby draining of
steam cylinder
active
––– ––– Automatic standby draining of
steam cylinder active.
No measures must be taken.
W37 Forced draining of
steam cylinder
active
––– ––– Forced draining of steam cylinder
active.
No measures must be taken.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cleopatra Cleo Eco Pro Steam generator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cleopatra Cleo Eco Pro Steam generator in the language / languages: English as an attachment in your email.

The manual is 10,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info