Manual Cisa Vision (page 8 of 24) (English, German, Dutch, French, Italian, Spanish)

788776

Zoom out

Zoom in

1/24

OPERATION 4

OPENING THE DOOR:

a) Press any button on the keypad. The keypad will light up.

b) Enter your personal code and press the button .

The green led will come on for 10 sec. : (effective time for opening the door).

c) Recall the bolts by turning the knob in a clockwise direction.

N. B.: when working in well-lit rooms, you can ignore step a) and pass directly to entering the personal code (step b).

RESETTING YOUR PERSONAL CODE:

If you forget your personal code number when the safe door is open, set a new code as follows:

a) Press at least one number key from 0 to 9.

b) Press the zero reset button within 20 seconds after having pressed the first key; the green led will illuminate for 20 seconds together

with an acoustic signal.

c) Type your personal code (min. 4 digits, max. 12) and press .

The red led will illuminate for 20 seconds .

d) Before the 20 seconds have elapsed enter your personal code again and press the ENTER key .

If the personal code has been correctly stored the two leds will switch off .

WARNING:

•THERE IS NO WAY TO OPEN THE DOOR IF YOU FORGET YOUR PERSONAL CODE WHEN THE SAFE IS CLOSED. YOU HAVE TO CONTACT CUSTOMER SERVICE FOR

CISA SAFES.

•ANY OPERATION THAT DOES NOT COMPLY WITH THE ABOVE INSTRUCTIONS WILL BE SIGNALLED BY A CONTINUOS RED LIGHT ACCOMPANIED BY A 2 SEC. .

ACOUSTIC SIGNAL. IN THIS CASE, REPEAT THE OPERATION CORRECTLY.

•IF THE RED LIGHT ILLUMINATES STEADILY AND AN ACOUSTIC SIGNAL SOUNDS WHILE YOU ARE STORING YOUR PERSONAL CODE, REMOVE THE BATTERIES AND RE-

INSERT THE BATTERIES THEM BEFORE REPEATING THE CODE STORAGE PROCEDURE.

•IF YOU ARE UNABLE TO REMEMBER THE COMBINATION, WRITE IT DOWN, BUT DO NOT KEEP THIS WRITTEN MEMO AT HOME.

•CHANGE THE COMBINATION FREQUENTLY TO AVOID LEAVING SIGNS OF WEAR ON THE KEYS USED.

•MAKE SURE THAT YOU ARE UNOBSERVED WHEN ENTERING THE COMBINATION ON THE KEYPAD.

•IT IS ADVISED TO USE PERSONAL CODES THAT ARE DIFFICULT FOR OTHERS TO GUESS (E.G.. DO NOT STORE VEHICLE REGISTRATION NUMBERS, DATES OF BIRTH,

ETC.)

SAFETY SYSTEMS:

TEMPORARY BLOCKING

•The safe will be temporarily blocked after three attempts to open it with the wrong code (the red led will light); the safe will remain

inoperable for 1 minute.

•At the end of this interval the red led will switch off and a new code can be set; if an incorrect code is entered again the safe will block

for another minute, and so forth until the correct code is entered: now the door can be opened and the block timer is reset.

TAMPER SIGNAL

•If, on entering the correct code the red led lights for 1 second before the green led, this indicates that a previous attempt has been made

to open the safe with the wrong code.

N.B.: The block and tamper signals are activated only if the incorrect codes detected are composed of a minimum of four and a maximum

of 12 digits. Otherwise no signals are generated.

WARNING:

POWER SUPPLY:

•Use four 1.5 V alkaline batteries, “AA” size, for the internal power supply. Do not use any type of battery carrier nor the 9V battery internally

(this is only suitable as an external power supply).

•Using flat batteries, an insufficient number of batteries, batteries with oxidised contacts, etc., may result in a general safe malfunction.

• It will therefore be necessary to supply the correct amount of power to the safe as illustrated in “DIRECTIONS FOR USE”.

• It is good practice to change the batteries at least once a year.

0.606.52.86.0_1 10-10-2005, 12:068

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cisa Vision in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cisa Vision Manual

Product: