588931
35
Zoom out
Zoom in
Previous page
1/38
Next page
Version
0.0061
PC Connect
033751
ID-Code
35
9. PC-mode
Before communication of the HAC5 with the computer can begin, the according programs (at least
one) and the interface (with the help of the driver) have to be installed.
9.1 Installation of the interface
Note: before you install the interface driver, please close all other programs and also deactivate the
antivirus scanner of your system, if not, problems may occur.
Plug interface directly into the computer or laptop (if a USB-Hub or multiple plug is used, problems
may occur).
With newer Windows systems, the plug will be automatically recognized and the hardware assistant
starts. Please follow the instructions and insert the CICLO-CD. After installation is completed, the
hardware assistant may appear again (e.g. under Windows XP), in that case please follow the ins
-
tructions on the screen once again. (Should no automatic installation take place, please look to the
point “problems” below).
If the installation is completed successfully, please check in the device manager of your system by
the point “ports” (COM and LTP) or “ports”. This is where the interface should be seen as USB
serial port” (or similar). An appointed Com-port will appear next to this in brackets. This Com-port is
needed later for the transfer, please note.
Problems:
Should the interface not be shown under “ports” please check if there is an exclamation or question
mark somewhere (possibly, it is shown as “unknown tool” or “USB-serial’). Double-click on the excla-
mation- or question mark, then install the driver (from the CICLO-CD) again.
9.2 Program installation
After successful installation of the interface, the desired program needs to be installed. In order to do
so, enter the CICLO-CD and double click the desired program. To install, please follow the instruc-
tions on the screen.
After installation open the program:
CICLOtour: adjust the corresponding port (which was shown in the tool manager) in the settings.
In the case that also other devices like the HAC4 (PRO) or CM4XXM should be imported, select
“confirm” in the device selection box. CICLOtour will ask you upon beginning the transfer for confir-
mation of the device type.
Click “save” at the right bottom, and then “OK” on the left.
HACtronic: adjust the corresponding port (which was shown in the tool manager) in the settings of
the HACtronic.
In the case that also other devices like the HAC4 (PRO) or CM4XXM should be imported, select
“confirm” in the device selection box. CICLOtour will ask you upon beginning the transfer for confir-
mation of the device type.
9.3 Transfer stored tours
To transfer the stored tours of the HAC5 into the pc, press the MR-button for 3 sec (main setting
mode). Select “PC-connect” with the UR-/OR-button and confirm with the MR-button. The display
now shows the version number in the upper display and the device ID in the lower display.
Now attach the interface clamp to the HAC5 in such a way that the contacts of the clamp are sitting
on the contacts of the backside of the HAC5, afterwards put down the HAC5 with the clamp in such
a way, that the display points upwards.
The transfer starts automatically by the program CICLOtour or HACtronic, when you click to the clo-
ck-icon in the icon list (or click to “data” and choose the transmission to the PC).
The program now shows the transfer screen and “wait”. After a few seconds the transfer should start
(do not move the HAC5 during transfer), if not, see below the point “problems”.
When the transfer is done, the program shows all transferred data in a list (raw data window).
Now take off the interface clamp, the HAC5 still shows the transfer display. Press the MR-button
shortly to leave the PC mode.
Note: Once the PC data transfer display is shown, the setting mode cannot be quit prematurely by
pressing the MR-button for 3 seconds. To quit, press MR-button short. Also, from this mode is no
automatic return to the operational mode, it must always be left manually.
Problems:
Should the PC data transfer not start automatically, click Cancel” in the program, remove the
interface from the HAC and attach again. Then start again the transfer in the program. The transfer
cannot begin automatically if the interface clamp doesn’t sit properly, so please make sure that the
contacts sit properly on the contacts of the HAC5.
Should the transfer be cancelled in the program with a notification of error, the clamp must be remo-
ved and before a new transfer is started the pc data transfer display must be left by short pres-
sing of the MR-button and re-selected by pressing the MR-button again. Then re-attach the clamp
and start again the data transfer on the PC.
Installation of the
interface
Program installation
Transfer stored tours
!
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo HAC 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo HAC 5 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo HAC 5

Ciclo HAC 5 Additional guide - English - 4 pages

Ciclo HAC 5 Additional guide - German - 4 pages

Ciclo HAC 5 Quick start guide - German - 2 pages

Ciclo HAC 5 User Manual - German - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info